User manual CRESTRON HBK-3000 SMK-3000

[. . . ] Routing the cables down through the center of the swivel assembly keeps the cables completely hidden from the work surface. Installation Guide ­ DOC. 6110 Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 · 1 Hatch Back & Swivel Mount Kits Crestron HBK-3000 & SMK-3000 Supplied Hardware The hardware supplied in the kits is listed in the following table. Supplied Hardware of the HBK-3000 and SMK-3000 (Hatchback & Swivel Mount Kits) HBK-3000 One (1) Metal Bracket One (1) Plastic Cover Four (4) Screws 4-40 X 3/16 inch SMK-3000* One (1) Swivel Mount Assembly One (1) Metal Bracket One (1) Metal Plate One (1) Plastic Cover Sixteen (16) Screws (4) 4-40 X 3/16-inch (4) 6-32 X 1/2-inch (4) 8-32 X 5/8-inch (4) 8-32 X 1-inch * The SMK-3000 mounting kit includes a template for preparing the mounting surface. Installation This section provides an installation procedure for each kit. The only tools required are #1, #2, and #3 Phillips screwdrivers. HBK-3000 Assembly/Installation Procedure To attach the HBK-3000 Hatch Back Kit to the TPS-3000 Touchpanel, refer to the illustration on page 3 and perform the associated procedures. [. . . ] Refer to the assembly view for the HBK-3000 Hatchback Kit above and remove the two screws A from the rear of the touchpanel that correspond to the Mounting Holes in the Metal Bracket. Installation Guide ­ DOC. 6110 Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 · 3 Hatch Back & Swivel Mount Kits Crestron HBK-3000 & SMK-3000 5. Put the Metal Bracket in position on the rear of the touchpanel base (mounting holes should align, and standoff posts should be oriented as shown in the illustration). Secure the Metal Bracket to the touchpanel using the two screws A removed in step 4. Refer to the illustration on page 5, and route the cables from the interface box up through the Metal Plate, through the mounting surface and through the Swivel Assembly, then through the area of the bracket shown in the figure, and connect to the appropriate touchpanel ports. Being careful to avoid damage to the cables, attach the Swivel Assembly to the base of the touchpanel, using the supplied four #6-32 X 1/2 inch screws C through the swivel assembly standoff posts into the threaded holes in the touchpanel base. Make certain the cables are not twisted or crimped and have sufficient slack at the port connections before fully tightening the screws. Make certain tab D is positioned to the front of the swivel assembly, and that it is directly opposite bent tab F, and place the touchpanel and swivel mount assembly down on the Mounting Surface. Hold the Metal Plate in position under the mounting surface and secure the assembly in place using the #8-32 screws G provided (use the 5/8-inch screws for surfaces 3/4-inch to 1 1/8-inches thick; use the 1-inch screws for surfaces 1 1/8 to 1 3/8 inches thick). Again, refer to the HBK-3000 illustration on page 3, and put the Plastic Cover in position and secure to the Metal Bracket using the four #4-40 X 3/16-inch screws B supplied. 4 · Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 Installation Guide ­ DOC. 6110 Crestron HBK-3000 & SMK-3000 Hatch Back & Swivel Mount Kits SMK-3000 Swivel Mount Kit Assembly Diagram Mounting Holes (2) A To Touchpanel Mounting B Holes (4) Bottom of Touchpanel Route Cables Through This Opening Swivel Assembly C D E F Mounting Surface FRONT Metal Plate G From Interface Box Installation Guide ­ DOC. 6110 Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 · 5 Hatch Back & Swivel Mount Kits Crestron HBK-3000 & SMK-3000 Further Inquiries If after reviewing this Installation Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: · In the US and Canada, call Crestron's corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. · In Latin America, call Crestron Latin America at +5255-5093-2160. · In Australia and New Zealand, call Crestron Pacific at +613-9480-2999. As of the date of manufacture, the HBK-3000 and SMK-3000 have been tested and found to comply with specifications for CE marking. Future Updates As Crestron improves functions, adds new features, and extends the capabilities of the HBK-3000 or SMK-3000, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website (www. crestron. com) periodically for manual update availability and its subjective value. Updates are available from the Downloads | Product Manuals section and are identified as an "Addendum" in the Download column. 6 · Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 Installation Guide ­ DOC. 6110 Crestron HBK-3000 & SMK-3000 Hatch Back & Swivel Mount Kits Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. [. . . ] CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. [. . . ]