User manual CRESTRON DTT-17

[. . . ] Crestron DTT-17 DualTouchTM Technology Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2006 Crestron Electronics, Inc DualTouchTM Technology Touchpanel Crestron DTT-17 Contents DualTouchTM Technology Touchpanel: DTT-17 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press Enter to save. NOTE: Manual changes invalidate the standard profile settings. Menu Position ­ Use the (-)/(+) buttons to move the menu to one of the available nine positions. Default is center position. 9. Reset ­ Use AUTO ADJUST to reset only the image parameters (menus 1 through 6). Backlight ­ Use the (-)/(+) buttons to decrease or increase the backlight brightness. 6343 DualTouchTM Technology Touchpanel: DTT-17 13 Crestron DTT-17 DualTouchTM Technology Touchpanel 11. Language ­ Use the (-)/(+) buttons to select a language for the display adjustment menus. Default is English. NOTE: There are additional setup screens that are resident in the UPX-2. Please refer to the latest version of the UPX-2 Operations Guide (Doc. 6276) for details. Using the Pen While working with the DTT-17, you can rest your hand on the surface of the display screen, just as if you were drawing on a sheet if paper. The pen is activated as soon as it enters proximity, about 0. 4 inches (1 cm) above the surface. This allows you to position the screen cursor before touching the pen tip to the surface. When the pen tip contacts the surface of the DTT-17, the tip switch is activated. Raising the tip above the surface of the DTT-17 is the same as releasing a mouse button. If there is no eraser switch on the top of the pen, the side switch is set to Eraser by default in the supporting MediaMarker NotebookTM application. If there is an eraser switch on the pen it works like the eraser on a pencil. Other settings for the pen are available via the UPX-2 setup screens. The pen comes with five extra tips since they wear with normal use. A worn tip can feel as though you are scratching the overlay, or that it just does not move as freely as it used to. The tip can be easily replaced with one of the included extra pen tips as shown below. Replacement pens and a 5-pack of replacement pen tips are available from the Wacom website (http://wacomdirect. wacom. com). NOTE: Be sure to have the pen part number and/or the touchpanel model number when ordering a replacement pen. 14 DualTouchTM Technology Touchpanel: DTT-17 Operations Guide ­ DOC. 6343 DualTouchTM Technology Touchpanel Grasp the worn tip with a pair of needle-nose pliers, tweezers, or similar instrument and pull out the tip. Crestron DTT-17 Firmly slide the new tip (square end first) into the barrel of the pen and press in until it stops. NOTE: A badly worn pen tip may damage the surface. Cleaning Keep the pen and screen surface clean. Dust and dirt particles can stick to the pen and cause wear to the screen surface. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. 07647, or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]