User manual CRESTRON DA-1550CW

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron DA-1550CW Docking Assembly for STX-1550CW Contents Docking Assembly for STX-1550CW: DA-1550CW Description Functional Description Physical Description Leading Specifications Setup Network Wiring Identity Code Installation Programming with SIMPL Windows Configure DA-1550CW Program BB/DA-1550CW Symbol Example Program Operation Normal Operation Manual Undocking of Touchpanel Problem Solving Troubleshooting Further Inquiries Future Updates Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty 1 1 1 1 4 4 4 5 6 8 9 9 10 10 10 12 15 15 17 17 18 18 18 Operations & Installation Guide - DOC. 5930 Contents · i Crestron DA-1550CW Docking Assembly for STX-1550CW Docking Assembly for STX-1550CW: DA-1550CW Description Functional Description The DA-1550CW docking assembly is wall-mounted hardware that is used to dock a Crestron SmarTouch STX-1550CW compact color touchpanel. Used with the BB-1550CW back box (sold separately), the DA-1550CW provides operating power, hard-wire communications with a standard Crestron remote control system (herein referred to as the Cresnet system), and recharges the Crestron High Performance Rechargeable Power Pack (ST-BTP) of the docked touchpanel. [. . . ] Install four hex screws (supplied) to finger-tight then, using a 5/64-inch hex wrench, tighten an additional 1/8-turn. Install Front Panel Operations & Installation Guide - DOC. 5930 Docking Assembly for STX-1550CW: DA-1550CW · 7 Docking Assembly for STX-1550CW 4. Crestron DA-1550CW As shown below, install the access hole plug into the access hole. Install Access Hole Plug Programming with SIMPL Windows SIMPL (Symbol Intensive Master Programming Language) is an easy-to-use programming language that is completely integrated and compatible with all Crestron system hardware. SIMPL Windows offers drag and drop functionality in a familiar Windows® environment. The two tables on the next page list the inputs and outputs, respectively, and their functional descriptions. Detail View of the BB/DA-1550CW Symbol in SIMPL Windows' Programming Manager NOTE: All signals listed in the tables on the next page are DIGITAL signals unless noted otherwise. A digital signal can be high (logic level of 1), low (logic level of 0), and also have rising edge (when it goes from low to high) and falling edge (from high to low) transitions. Depending upon how the symbol was created, symbol signals may work at the logic levels, some may work on transitions. Operations & Installation Guide - DOC. 5930 Docking Assembly for STX-1550CW: DA-1550CW · 9 Docking Assembly for STX-1550CW BB/DA-1550CW Symbol Input Description Crestron DA-1550CW INPUT UNLATCH (Unlock in earlier versions of SIMPL Windows. ) FUNCTION(S) Edge sensitive. Unlatches the back box for 5-seconds when the edge of the signal is received. The back box may not be unlatched for 1-second after the latch is engaged. BB/DA-1550CW Symbol Output Descriptions OUTPUTS FUNCTION(S) UNLATCHED 1 when the latch is open, 0 when the latch is closed. (Unlock-FB in earlier versions of SIMPL Windows. ) PANELPRESENT 1 when the touchpanel is docked, 0 when the touchpanel is not docked. 1 when the touchpanel is docked and the ST-BTP is charging, CHARGING 0 otherwise (i. e. 1 when the touchpanel is docked and charging is complete, 0 CHARGEDONE otherwise (i. e. hardware problem with the CHARGEFAULT touchpanel, poor contact with the charger, a network voltage problem, etc. ), 0 when no fault is present. Example Program An example program for the DA-1550CW is available from the Downloads page (EXAMPLES Library) of Crestron's website (www. crestron. com). Search for DA1550CW. ZIP that contains the example program, associated files and a README. TXT file that describes the program. New users are required to register in order to obtain access to the FTP site. Operation The DA-1550CW docks the STX-1550CW touchpanel, provides power and communication, and recharges the ST-BTP. Operation consists of docking the touchpanel (performed by hand) into the DA-1550CW or undocking electrically via the control system and then removing by hand. Provisions have also been incorporated to allow the touchpanel to be undocked manually. Normal Operation Normal operation of the DA-1550CW is described in the next two sections. Docking the STX-1550CW Docking of the STX-1550CW is performed by hand by inserting the bottom edge of the touchpanel into the DA-1550CW and snapping it into place. NOTE: Do not dock the STX-1550CW into the DA-1550CW without the ST-BTP being installed in the touchpanel. Operating power for the DA-1550CW is supplied through the electrical contacts of the ST-BTP. If the ST-BTP is not installed, the DA-1550CW will not electrically unlatch the touchpanel. 10 · Docking Assembly for STX-1550CW: DA-1550CW Operations & Installation Guide - DOC. 5930 Crestron DA-1550CW 1. Docking Assembly for STX-1550CW Refer to the diagram below. Insert the bottom edge of touchpanel docking plate (located on the rear of the touchpanel) into DA-1550CW directly behind the front panel. Insert STX-1550CW 2. Refer to the diagram below. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]