User manual CRESTRON CPC-CAMI

[. . . ] Crestron CPC-CAMI Pan/Tilt Camera Head with Control Interface Contents Pan/Tilt Camera Head with Control Interface: CPC-CAMI 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Leading Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] These codes are recognized by a two-digit hexadecimal number from 03 to FE. The NET ID of each unit must match an ID CODE specified in the SIMPL Windows program. The NET ID of each CPC-CAMI has been factory set to 34, but may be changed from the PC via VisionToolsTM Pro-e (VT Pro-e) or SIMPLTM Windows. The method for changing the unit's NET ID is identical regardless of the software chosen. Attach the CPC-CAMI to the control system (verify that the software is running) and complete the following steps to change the NET ID. Disconnect all network devices from the control system, except for the one CPC-CAMI that needs to have its NET ID code changed. Select Tools | ViewPort to open the "Crestron Viewport" dialog box. The software checks the baud rate and then opens the "Set Network ID" dialog box. The NET ID of the CPC-CAMI (default is 34) appears in the box below the list. When the newly assigned NET ID appears, select the Set ID button to initiate the change. The software responds with a successful message to confirm the new NET ID. 10 · Pan/Tilt Camera Head with Control Interface: CPC-CAMI Operations Guide - DOC. 9. Pan/Tilt Camera Head with Control Interface To verify this procedure, select Diagnostics | Report Network Devices. Reconnect other network or modular devices that were disconnected in step 1. Preparation for Use Refer to the hookup diagram below. Other than connecting the correct jumper board first and making the power connection last, complete the connections in any order. NOTE: Before making connections to the NET port, review the latest revision of the Network Modular Cable Requirements (Doc. Most 4-conductor phone cables are wired in a crisscross fashion and are not compatible with Crestron equipment. The wiring document can be obtained from the Downloads page (CABLES and MANUALS Libraries) of the Crestron website (www. crestron. com). NOTE: To insure safe operation of the CPC-CAMI, all cables around the unit must be properly "dressed" so that the cables do not strike surrounding surfaces or equipment which would endanger safe system movement when in operation. Hookup Connections for CPC-CAMI Initialization There are no specific steps required to initialize the CPC-CAMI. The unit is ready four seconds after applying power. Operations Guide - DOC. 5726A Pan/Tilt Camera Head with Control Interface: CPC-CAMI · 11 Pan/Tilt Camera Head with Control Interface Limit Stop Adjustment Crestron CPC-CAMI Two locking screws are found on each rotating disk on the CPC-CAMI. Loosen both pan (horizontal drive) and tilt (vertical drive) locking screws. Slide a loosened locking screw until it engages the pan sensor; tighten the locking screw. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]