User manual CRESTRON CPC-2000A

[. . . ] Crestron CPC-2000A Touchpanel with Dual Joysticks Contents Touchpanel with Dual Joysticks: CPC-2000A 1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Cresnet network identity number (NET ID) is displayed in the top left corner of the Interface Menu. NET ID is the two-digit hexadecimal number represented by ## in the figure for illustrative purposes. The hexadecimal number can range from 03 to FE and must correspond to the NET ID set in the SIMPL Windows program. Matching NET IDs between touchpanel and the program is required if data is to be successfully transferred or new touchpanel screens are to be loaded. Two side-by-side buttons adjacent to the hexadecimal display, < CRESNET ID and CRESNET ID >, decrease and increase the NET ID by one, respectively. Occasionally the touchpanel can be used in local demo mode where it merely displays various menus, but does not communicate with the control system. In local mode, the directory buttons change pages, but buttons requiring feedback do not work. Two centrally located buttons on the Interface Menu, CRESNET II and LOCAL, determine communication mode. Select LOCAL to set the touchpanel into demo mode and CRESNET II for normal control system communication mode. Two side-by-side buttons, RS-232 ON and RS-232 OFF, are centrally located on the Interface Menu. Since there is no RS-232 port on the unit, verify that the RS-232 OFF button is selected. Furthermore, there is no need to use the RS232 SETTINGS button on the Interface Menu. Sound Menu Sound Menu The SOUND button, located at the top right corner of the Setup Menu, is used to display the Sound Menu, shown to the left of this paragraph. Confirmation of a button press on a touchpanel is acknowledged by an audible click assuming this feature is enabled. To enable this feature, verify that the KEYCLICK ON button is active (red). Volume of the audible click is controlled with the VOLUME UP and VOLUME DOWN buttons. Return Select the RETURN button, located at the lower right corner of the Setup Menu, after setup parameters have been set. Operations Guide - DOC. 5801A Touchpanel with Dual Joysticks: CPC-2000A · 9 Touchpanel with Dual Joysticks Save Setup and Run Program Crestron CPC-2000A The SAVE SETUP AND RUN PROGRAM button, located at the upper right corner of the Main Menu, saves all of the setup information to EPROM and displays the main page that has been programmed into your system. Programming The touchpanel component of the CPC-2000A is programmed as if it were a CT-1600 touchpanel. Therefore, when designing projects in an earlier version of VT Pro for use with the CPC-2000A, choose CT-1600 as the touchpanel target type. The latest version of VT Pro-e has CPC-2000A available as a target type. However, instructions for screen design are not presented in this guide; refer to VT Pro-e's help file for assistance. The software also provides a step-by-step tutorial to fully acquaint the novice programmer. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]