User manual CRESTRON CNX-DVP4

[. . . ] Crestron CNX-DVP4 Digital Video Processor Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc. Crestron CNX-DVP4 Digital Video Processor Contents Getting Started with the CNX-DVP4 ­ Quick Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Digital Video Processor: CNX-DVP4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This should display a window that gives the IP address and port number. Troubleshooting Communications Use the following checklist if communication cannot be established with the CNXDVP4. As described previously, an RS-232 connection requires a straight-through serial cable. With a TCP/IP connection, you must use a CAT5 cable with 8-pin RJ45 connectors. With a serial connection, verify that the correct COM port on the PC has been selected. Some computers have more than one COM port; some may be internal (e. g. , for a modem). Consult the manufacturer's documentation for further information about the COM ports on your PC. Open Viewport and click Setup | Communications Settings to display the "Port Settings" window. Set the baud rate of the PC to 115200 (use with new . cuz files, version 3. 0. 17 and higher) or 57600 (use with older . cuz files). If communication still cannot be established, reinitialize the unit by recycling power (the unit takes approximately 25 seconds to reboot). If the connection is established, the Viewport console should display some text and the <DVP4> prompt. If communication still cannot be established, contact Crestron Customer Support. 2. 3. e. 4. Verify that no other software is using the same COM port. Compiling and Uploading a Program to the Control System After you have completed your SIMPL Windows program you must compile and upload the program to the control system. To compile the program, simply click the Convert/Compile button on the SIMPL Windows toolbar, or select Project | Convert/Compile (you can also press F12). After the operation is complete, a window will display information about the program such as the number and type of signals, and memory usage. The compiled program will be stored as an SPZ file in the same directory as the source file. Immediately after compiling the program you are prompted to transfer the file to the control system. on the SIMPL Windows toolbar to open the Click the Transfer button Send Program window (refer to the following graphic). Click Browse, Digital Video Processor: CNX- DVP4 · 51 Operations Guide ­ DOC. 8170A Digital Video Processor Crestron CNX-DVP4 locate the SPZ file and click Open. This will display the program's header information and enable one or both of the What to Send check boxes. If the program does not contain any SIMPL+ modules only the SIMPL Program check box will be enabled. If it does contain SIMPL+ modules, then the SIMPL+ check box will also be enabled. [. . . ] Enclose aa note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]