User manual CRESTRON CNAMPX-7X200

[. . . ] This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier Contents 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The NET ID of the unit must match an ID code specified in the SIMPL Windows program. The NET IDs of multiple CNAMPX-7X200s in the same system must be unique. NET IDs are changed from a personal computer (PC) via the Crestron Viewport. NOTE: For detailed information on establishing communication between the PC and Control System, refer to the network's Control System Operations Guide. Ensure that the CNAMPX-7X200 is the only device connected to the control system (verify that the software is running). The software checks the baud rate and then opens the "Set Network ID" window. In the "Set Network ID" window, select the CNAMPX-7X200 from the Current Network Devices text window. From the Choose the new network ID for the selected device (Hex): text box, select the new Net ID for the CNAMPX-7X200. In the Current Network Devices text window, verify the new NET ID code. 9. NOTE: The new NET ID code may also be verified by selecting Diagnostic | Report Network Devices in the Viewport (alternately, select F4). Repeat this procedure for each CNAMPX-7X200 to be added to the system. Hookup Refer to the following suggested configuration diagram, and make the connections to the input and output connectors of the CNAMPX-7X200 amplifier appropriate for the intended operation of the unit. Other than making the power connection last, complete the connections in any order. The power cord is supplied, but RCA audio cables, speaker wire, or Cresnet cables are not provided. NOTE: Each of the seven amplifier channels are functionally identical and can be connected to a surround-sound processor in any convenient arrangement. NOTE: Refer to "Network Wiring" on page 6 when making connections to the port labeled NET. Operations Guide ­ DOC. 8179 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 · 7 7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200 NOTE: U. S. Use only the supplied power cord, or equivalent, to connect to the AC power source. Suggested Hookup Connections for the CNAMPX-7X200 SURROUND SOUND PROCESSOR SIDE REAR CENTER FRONT L R SURROUND SOUND OUT SUBWOOFER TO SUBWOOFER CNAMPX-7X200 SURROUND SOUND AMPLIFIER LEFT FRONT RIGHT FRONT LEFT SIDE RIGHT SIDE LEFT REAR RIGHT REAR CENTER (FRONT) Typical System Configuration The following figure shows a typical head-end/room audio configuration using the CNAMPX-7X200. 8 · 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide ­ DOC. 8179 Crestron CNAMPX-7X200 7 Channel Surround-Sound Amplifier Programming You can create a program that allows you to control the CNAMPX-7X200 through a Crestron control system using the Crestron programming tools Crestron Application BuilderTM (AppBuilder) and SIMPLTM Windows®. These tools are intended for users with different levels of programming knowledge. The flexibility of each tool is proportional to the degree of programming expertise (i. e. , the more flexible, the more a programmer needs to know and account for). Of course, one can initiate programming using the easiest method (Crestron AppBuilder) and use advanced techniques that are available from SIMPL Windows to customize the job. The following are recommended software version requirements for the PC: · · · SIMPL Windows version 2. 01. 05 or later. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]