User manual CRESTRON CLW-DIM1 DIMS1 SLVD1

[. . . ] CLW-DIM1, DIMS1, & SLVD1(W/A/B) Introduction Features and Functions The CLW-DIM1 (-DIM1) is a stand-alone wall box dimmer that can also act as a Cresnet® device that reports to a Crestron® control processor. The CLW-DIM1 has two preset lighting levels that can be adjusted (refer to note below). The CLW-DIM1 also includes two isolated, non-polarized Cresnet wires (plus a ground wire) for connecting to the Cresnet network over a twisted pair wire with shield. NOTE: The two preset levels are noted as Preset 1-High and Preset 1- Low. [. . . ] Splice the gray wires of the -DIMS1 to the Class 2 low voltage wires connected to the Crestron control system or a Crestron connection block device. Push the wires and the splices into a hole in the drywall to provide the necessary separation. Wiring a -DIM(S)1 (No Slaves) The following describes the installation of a stand-alone -DIM1 or -DIMS1. Pull Class 2 low voltage wires through a hole in the drywall located outside of the electrical box, to the Crestron control system or a Crestron connection block device. Leave wires outside of the wallbox for connection to the -DIM1 or -DIMS1. NOTE: Alternate wiring methods may be used for the Class 2 wiring connection. The BLACK wire (Cresnet ground) paired with the GRAY (Cresnet) wires is #22 AWG. NOTE: Since the -DIMS1 is installed without a -SLVD1, the BLUE lead (Slave) should be capped. Alternative Wiring For situations where a neutral is not present or other scenarios that may be encountered during installation, refer to the "Stand-Alone Installations" section of "Appendix: Wiring Diagrams" on page 8. Splice the gray wires of the -DIM1 or -DIMS1 to the Class 2 low voltage wires connected to the Crestron control system or a Crestron connection block device. Push the wires and the splices into a hole in the drywall to provide the necessary separation. Push all power wires back into the wallbox and fasten the device to the wallbox with the provided screws. 6250A Stand Alone Wall Box Dimmer: CLW-DIM1, DIMS1, & SLVD1 · 5 CLW-DIM1, DIMS1, & SLVD1(W/A/B) 5. Push all power wires back into the wallbox and fasten the devices to their respective wallboxes with the provided screws. The lighting level will stop at maximum brightness (100%) if the lighting level was ramping up or minimum brightness (0%) if the lighting level was ramping down. To continue ramping the lighting level in the opposite direction, release the pushbutton, then press and hold the pushbutton again. If the lighting level is to be stored as a preset, move the mode selection switch to the PRE position. 7. Operation The -DIM1, -DIMS1, and -SLVD1 have one large pushbutton. The function of the pushbutton is determined by the position of the mode selection switch. It emulates the operation of the -DIMS1 to which it is connected unless the mode selection switch of the master is set to "OFF". Buttons of CLW-DIM1, -DIMS1, and -SLVD1 PRE NOTE: Before storing a preset, the lighting must be adjusted to the desired level while in the ADJ mode. When the switch is in the PRE position, it is in the preset mode and can be used to recall and/or store preset lighting levels. The pushbutton is used to recall and/or store the "Preset 1-High" and "Preset 1-Low" presets. Pressing and releasing the pushbutton will fade to the preset lighting level over a preset amount of time*. [. . . ] Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. [. . . ]