User manual CRESTRON CHV-TSTAT CHV-THSTAT FIRMWARE BETWEEN 1.1-2.0

[. . . ] Crestron CHV-TSTAT & CHV-THSTAT Thermostats Operations and Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc. Crestron CHV-TSTAT and CHV-THSTAT Thermostats Contents Quick Installation Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Thermostats: CHV-TSTAT and CHV-THSTAT 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · · · · H1 ­ Single Stage Heating H2 ­ Two Stage Heating C1 ­ Single Stage Cooling C2 ­ Two Stage Cooling. NOTE: This screen bypasses all system delays and is used by the installer to manually operate the HVAC system. Only one system can be run at a time. Heat Call Choose Off, H1, or H2 SETUP: SERVICE/TEST Heat Call: OFF Cool Call: OFF Aux Heat Call: OFF Humidifier Call: OFF Fan Run Call: OFF MODE Cool Call Choose Off, C1 or C2 Aux Heat (ON or Off) Only appears on heat pump systems Humidifier Call (On or Off) CHV-THSTAT only Fan Run Call (ON or OFF) VIEW CRESTRON Press MODE button to return to the first screen. Simultaneously press and hold the MODE and VIEW buttons to return to normal operation mode. 20 · Thermostats: CHV-TSTAT and CHV-THSTAT Operations and Installation Guide ­ DOC. 8163A Crestron CHV-TSTAT and CHV-THSTAT Thermostats Operating the Thermostat After setup, configure the thermostat using the following screens. Main Screen MODE 66 43 o F VIEW % HEATING HEAT ONLY ON LINE H1 68 F o The Main Screen displays the Current Temperature, System Mode, Fan Mode, and Set Point temperatures. NOTE: If you selected Yes in setup screen #6 for "Dual Setpoint Auto", pressing MODE toggles between the Heat and Cool setpoints. This screen also indicates the system currently running: H1 ­ Heat System or Stage 1 Heat System H2 ­ Stage 2 Heat System AX ­ Auxiliary Heating System C1 ­ Cooling System or Stage 1 Cooling System C2 ­ Stage 2 Cooling System MODE MODE Button It may also be necessary to access the following series of screens. Pressing the MODE button allows the user to access the following screens: 1. SYSTEM MODE The "System Mode" screen appears when the MODE button is initially pressed. Use the up and down arrow buttons to select HEAT, COOL, AUTO, OFF or AUX Heat Only. NOTE: The AUTO selection allows the system to switch between Heat and Cool automatically as needed to maintain the temperature. NOTE: The AUX HEAT ONLY is for the backup heating system on Heat Pump systems only. Allows the backup system to operate without operating the heat pump. System Mode HEAT COOL AUTO OFF AUX HEAT ONLY VIEW Fan Mode Screen MODE 2. FAN MODE Pressing the MODE button again displays the "Fan Mode" screen. NOTE: In AUTO, the fan runs only when the system calls for heat or cool. In ON, the fan runs continuously. Thermostats: CHV-TSTAT and CHV-THSTAT · 21 Fan Mode AUTO ON VIEW Operations and Installation Guide ­ DOC. 8163A Thermostats Crestron CHV-TSTAT and CHV-THSTAT Humidifier Screen MODE 3. Humidifier (CHV-THSTAT ONLY) Pressing the MODE button displays the "Humidifier" screen. Use the up and down arrow buttons to select ENABLED or DISABLED. Humidifier ENABLED DISABLED VIEW Crestron System Screen MODE 4. CRESTRON SYSTEM Pressing the MODE button again displays the Crestron System screen. ONLINE ­ Data flows both ways, to and from the thermostat, enabling adjustment from a remote location. HOLD ­ Data flows one way, from the thermostat, blocking system commands to change the temperature and humidity when you do not want the current settings reset. Crestron Sys ONLINE HOLD VIEW Global Update Screen MODE 5. GLOBAL UPDATE Pressing the MODE button again displays the Global Update screen. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]