User manual CRESTRON CHV-RTS CHV-RTHS

[. . . ] 8189A Remote Temperature/Humidity Sensors Crestron CHV-RTS/CHV-RTHS Specifications SPECIFICATION Temperature Range (CHVRTS and CHV-RTHS) Humidity Range (CHVRTHS only) DETAILS -30º to 120ºF (-34. 44Cº to 48. 89ºC)* 0 to 100% *Thermostat front panel indoor temperature display is limited to a range of 0 ­ 110ºF (-18º to 43ºC). The front panel outdoor thermostat display will display the full range of temperature. Physical Description Refer to the illustrations below and on the following page. The sensor body is 2. 22 in (5. 64 cm) long, and mounts nearly flush to the wall. The CHV-RTS and CHV-RTHS remote sensors are contained in a cylindrical plastic body with a metal cap. [. . . ] NOTE: Crestron strongly recommends low-capacitance twisted pair wire such as CAT3 (up to 250 ft, 76. 2 m) or CAT5 (up to 500 ft, 152. 4 m) network cable when using remote sensors. Maximum distance from sensor to thermostat is 500 ft, 152. 4 m If multi-conductor cables are used, the leftover conductors must NOT be used for other purposes and must be left unconnected at both ends. In situations where ordinary two-conductor thermostat wire (18 to 20 gauge) has been installed, it may be used for runs up to 100 feet (30. 48 meters). Other cable types are satisfactory, provided the total capacitance is less than 7000 pF. Connect the wires from the thermostat to the 10 in (25. 4 cm) sensor pigtail (22 AWG x12" black/black twisted pair) using wire nuts. (Refer to "Hardware Hookup" on page 5). 4 · Remote Temperature/Humidity Sensors Installation Guide ­ DOC. 8189A Crestron CHV-RTS/CHV-RTHS Remote Temperature/Humidity Sensors 7. Press fit the sensor into the hole; the clips on either side of the sensor hold it in place. Wire Nuts Pigtail Wires from Sensor Wires from Thermostat Mounting Clips 1in (2. 54cm) Hole NOTE: The face of the sensor may be painted or wallpapered to match the wall. However, keep the small gap around the outer edge clear of any obstructions. Hardware Hookup The sensors are connected to the remote sensor terminals RS1, RS2, and a common connection RSR on the rear plastic housing of the thermostat. The thermostat terminal blocks mate to pins protruding out of the front thermostat assembly. Thermostat firmware release 1. x supports the addition of only two optional remote sensors (temperature and/or temperature/humidity) per thermostat on sensor inputs RS1 and RS2. Thermostat firmware release 2. x supports up to four optional temperature (CHV-RTS) or slab sensors (CHV-RSS) or two temperature/humidity sensors (CHV-RTHS). If you are using one temperature/humidity sensor, then you may add two temperature sensors (CHV-RTS or CHV-RSS) to the other sensor input. Installation Guide - DOC. 8189A Remote Temperature/Humidity Sensors · 5 Remote Temperature/Humidity Sensors Crestron CHV-RTS/CHV-RTHS Connection Example 1: Connecting two temperature/humidity sensors to the thermostat (maximum number of temperature/humidity sensors): NOTE: Sensor wiring is non-polarized 1. Remote sensor 2 connected to RS2 and RSR Remote Sensor 1 Remote Sensor 2 TOP 24(C) RHU 24(R) HUM RSR RSR RS1 RS2 24V Y G Z Thermostat Backplate NETWORK Connection Example 2: Connecting four temperature sensors (CHV-RTS) to the thermostat (maximum number of temperature sensors): 1. Remote Sensor 2 and 4 are connected to RS2 and RSR. Remote Temperature Sensor 4 Remote Temperature Sensor 3 Remote Temperature Sensor 2 Remote Temperature Sensor 1 TOP 24(C) RHU 24(R) HUM RSR RSR RS1 RS2 24V Y G Z Thermostat Backplate 6 · Remote Temperature/Humidity Sensors NETWORK Installation Guide ­ DOC. 8189A Crestron CHV-RTS/CHV-RTHS Remote Temperature/Humidity Sensors Connection Example 3: Connecting one temperature/humidity sensor (CHV-RTHS) and two temperature sensors (CHV-RTS) to the thermostat (maximum number of sensors when using one temperature/humidity sensor): 1. Remote Temperature Sensor 1 and 2 are connected to RS2 and RSR. Remote Temperature Sensor 2 Remote Temperature/Humidity Sensor 1 Remote Temperature Sensor 1 TOP 24(C) RHU 24(R) HUM RSR RSR RS1 RS2 24V Y G Z Thermostat Backplate NETWORK NOTE: For additional firmware details, refer to the latest version of the Crestron CHV-TSTAT/CHV-THSTAT Thermostats Operations and Installation Guide, Doc. These documents are available on the Crestron website (www. crestron. com). Installation Guide - DOC. 8189A Remote Temperature/Humidity Sensors · 7 Remote Temperature/Humidity Sensors Crestron CHV-RTS/CHV-RTHS Problem Solving Further Inquiries If after reviewing this Installation Guide, you cannot locate specific information or have questions, please take advantage of the Crestron award winning customer service team by calling: · In the US and Canada, call Crestron's corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. [. . . ] 07647, or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]