User manual CRESTRON C2N-DAP8

[. . . ] Crestron C2N-DAP8 Digital Audio Processor Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", "Pro Logic II", "Dolby Digital", "Dolby Digital 5. 1", and the double-D symbol are trademarks of Dolby laboratories. "DTS", "DTS Digital Surround Sound", "DTS-ES Extended Surround", "DTS Virtual 5. 1", "NEO:5", and "Neo:6" are trademarks of Digital Theater Systems, Inc. [. . . ] The program is supplied designed to work with a Crestron TPS-4500 touchpanel and a 2-Series processor. If your system uses a different touchpanel, convert the program for that touchpanel. Preparation In preparation for running the Example Program, do the following: 1. Verify that all the necessary procedures detailed in "Setup" on page 9 have been completed. Verify that communication setup procedures described in "Communication Settings" on page 45 have been completed. After downloading the Example Program from the Crestron website, use the instructions given in "Upload via Crestron Viewport" on page 47 , to load the . spz program to the control system and load the . vtz program to the touchpanel. Running the Example Program Once the programs are loaded to the touchpanel and the control system, the main screen appears on the touchpanel. Operations Guide ­ DOC. 8186 Digital Audio Processor: C2N-DAP8 · 33 Digital Audio Processor Example Program Main Screen Crestron C2N-DAP8 The MUTE button and the up and down arrows at the lower right control the sound being supplied to the available speakers indicated by the LEDs in the upper right corner. The SOURCE SELECT pane is used to select the digital or analog audio source material connected to the unit's input ports. The UTILITY pane lets you select the AUDIO switching utilities, or SYSTEM SETUP. (The VIDEO switching utility does not apply for the C2N-DAP8. ) The TONE CONTROL pane provides controls appropriate to the chosen audio source and decoding mode. For example, the DYNAMIC RANGE selections MIN, STD, and MAX, shown in the illustration, apply the indicated amount of compression for Dolby Digital sources, as follows: MIN provides the highest compression ratio, bringing dynamic range close to that of a TV broadcast. STD provides the dynamic range recommended by sound engineers for general home viewing. MAX provides the full dynamic range of a cinema. System Setup To begin, select SYSTEM SETUP. The display provides a set of buttons you use to select the parts of the system to be configured--SPEAKER CONFIG, AUDIO CONFIG, and EQ'S--plus AUDIO SWITCH which is used to set the internal routing of audio signals. (The VIDEO SWITCH selection does not function for the C2N-DAP8. ) Initially, the large screen area to the right is blank. The screen displays the SPEAKER CONFIG window. 34 · Digital Audio Processor: C2N-DAP8 Operations Guide - DOC. 8186 Crestron C2N-DAP8 SPEAKER CONFIG Window Digital Audio Processor Use this screen to specify the speaker arrangement of your system and to set the crossover frequency for the subwoofer. Click on the appropriate buttons to identify the existing speaker arrangement. Select the appropriate one of the X-OVER buttons to specify the crossover frequency for the subwoofer (if present). The distinction between large and small speakers here is their ability to provide effective sound in the low frequency range (120 Hz and below), not their physical size. Low frequency signals appearing in channels with speakers designated as small will be filtered out and routed to the subwoofer. Check the frequency range rating of all speakers to determine their proper setting. Audio Configuration Select the AUDIO CONFIG button. Use this screen to set up the volume trims, the delays, and the noise generator settings. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]