User manual CRESTRON C2N-CAMIDSPT

[. . . ] Crestron C2N-CAMIDSPT Camera Interface, Digital Servo Pan Tilt Head Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names, and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc. Crestron C2N-CAMIDSPT Camera Interface, Digital Servo Pan Tilt Head Contents Camera Interface, Digital Servo Pan Tilt Head: C2N-CAMIDSPT 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Another typical configuration would include a Crestron Camera Controller such as the CPC-2000A. (A complete configuration for control of a remote video camera would include distribution of the camera's video output to a local video monitor so you can see the results of your setting adjustments. ) Typical Configuration for Control of Remote Video Camera/Lens Functions Power Up Conditions At power up, the CAMIDSPT executes a short series of pan/tilt movement while it calibrates its home position. The unit must have unrestricted movement in a range of ±30 degrees. If no user program is running, the pan/tilt will return to the home position. If a user program is running, the unit will return to the last position specified by the position analog input joins. In order for the lens output drivers to be enabled, the attached lens must be powered up at the same time or before the CAMIDSPT is powered. If the local joystick has been operated since the last power up, a calibration routine will be performed. Limit Stop Adjustment Two adjustable stops are supplied for each rotating disk on the CAMIDSPT. For this procedure, operation of the CAMIDSPT is controlled through the mini joystick. Refer to "Mini Joystick" on page 9 for more information. 18 · Camera Interface, Digital Servo Pan Tilt Head: C2N-CAMIDSPT Operations Guide - DOC. 6262A Crestron C2N-CAMIDSPT Camera Interface, Digital Servo Pan Tilt Head NOTE: Adjustable stops must be properly installed prior to calibration or operation of the CAMIDSPT. Apply Cresnet power to the CAMIDSPT, and use the mini joystick to adjust the pan and tilt discs away from their default positions adjacent to the fixed hard stops. Install both pan and tilt adjustable stops by inserting the nut portions into the slots of the rotating discs; move them away from the slot and tighten the screws just enough to keep them from sliding. Slide the closest adjustable stop until it engages the pan hard stop; tighten the locking screw. Slowly rotate the camera/lens assembly to the desired right-pan limit. Slide the other adjustable stop until it engages the pan hard stop; tighten the locking screw. Slide the closest adjustable stop until it engages the tilt hard stop; tighten the locking screw. Slowly rotate the camera/lens assembly to the desired down-tilt limit. Slide the other adjustable stop until it engages the tilt hard stop; tighten the locking screw. Verify the stop positions at slow speeds and then at full speed to ensure proper settings. 2. 3. 4. 5. 6. 7. NOTE: Hard stops should not be set any closer to the pan and tilt home positions than ±30 degrees. Hard stops set closer will prevent the unit from executing the power-up homing routine. Dimples on each rotating disc line up with dimples on the unit housing when the unit is in home position. Cycle power to the CAMIDSPT--the unit will go through its initialization motions. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]