User manual CRESTRON C2N-CAMIDJ

[. . . ] Crestron C2N-CAMIDJ Digital Joystick Camera Controller Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc. Crestron C2N-CAMIDJ Digital Joystick Camera Controller Contents Digital Joystick Camera Controller: C2N-CAMIDJ 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Thus, serial signals are used to facilitate the transmission of serial data (strings of characters). These signals can be generated by incoming data on a COM port or by a symbol that has a serial output. Input/Output Signals The following table lists functional descriptions for the CAMIDJ inputs and outputs. Many of the signal descriptions include information relative to the CamiDJ Interface Module included in the CAMIDJ example program. Refer to the Appendix for a functional description of the CamiDJ Interface Module. Operations Guide ­ DOC. 6341 Digital Joystick Camera Controller: C2N-CAMIDJ · 17 Digital Joystick Camera Controller CAMIDJ Input and Output Signal Descriptions Crestron C2N-CAMIDJ SIGNAL TYPE AND NAME DESCRIPTION Activates the LED feedback of the IRIS AUTO button for as long as the input is high. Digital input: <IrisAutoLED-F> If used with the CamiDJ Interface, this input will be connected to the {{IrisAutoLED-F>>C2N-CAMIDJ}} output of the module. Activation of the signal indicates that iris auto adjust mode has been selected. High/1 (level sensitive) = Activate LED; Low/0 = Release LED Indicates that the IRIS AUTO button has been pressed. The output remains high for as long as the button is pressed. Digital output: <IrisAutoBtn> If used with the CamiDJ Interface, this output will be connected to the {{C2N-CAMIDJ>>IrisAutoBtn}} input of the module. When connected to the CamiDJ Interface, this signal is used to activate the iris auto adjust mode. High/1 = IRIS AUTO button pressed; Low/0 = Iris auto adjust mode released Activates the LED feedback of the IRIS MANUAL button for as long as the input is high. If used with the CamiDJ Interface, this input will be connected to the {{IrisManualLED-F>>C2N-CAMIDJ}} output of the module. Activation of the signal indicates that the iris manual adjust mode has been selected. The unit will remain in iris manual adjust mode for as long as the encoder wheel is being rotated. If there is no wheel rotation for 20 seconds, the unit will revert to focus adjust mode and the IRIS MANUAL button will show blinking feedback on the LED. The button would need to be pressed again to re-enter iris manual adjust mode. High/1 (level sensitive) = Activate LED; Low/0 = Release LED Indicates that the IRIS MANUAL button is being pressed. The output remains high for as long as the IRIS MANUAL button is pressed. Digital input: <IrisManualLED-F> Digital output: <IrisManualBtn> If used with the CamiDJ Interface, this output will be connected to the {{C2N-CAMIDJ>>IrisManualBtn}} input of the module. When connected to the CamiDJ Interface, this output is used to activate the iris manual adjust mode. High/1 = IRIS MANUAL button pressed; Low/0 = IRIS MANUAL button released Activates the LED feedback of the FOCUS button for as long as the input is high. If used with the CamiDJ Interface, this input will be connected to the {{FocusLED-F>>C2N-CAMIDJ}} output of the module. Activation of the signal will indicate that the focus adjust mode (encoder wheel controls focus) has been selected. The unit will revert to focus adjust mode (exiting speed adjust mode or iris manual adjust mode) after a timeout period of 20 seconds has passed with no movement of the encoder wheel. [. . . ] To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]