User manual CRESTRON B-G2-FP B-G3-FP

[. . . ] The faceplate unit consists of a removable 2 or 3-gang plastic faceplate and a 2 or 3-gang detent plate. Refer to the NOTE on page 6 for metal faceplate installation instructions. Each button assembly consists of a rear speaker, and a male port (standard Cresnet network port labeled 24 Y Z G). The port provides operating power and communications to/from the keypad Installation Guide - DOC. [. . . ] Twist together the ends of the wires that share a pin on the network connector, and tin the twisted connection. Insert the tinned connection into the Cresnet connector and tighten the retaining screw. Repeat the procedure for the other three conductors. Identity Code Every equipment and user interface within the network requires a unique identity code (NET ID). Refer to latest version of the Operations and Installation Guide for the Single Gang Keypads, Doc. 8173, for procedures on setting the NET ID. Installation NOTE: For simplicity, the following procedure is for a 2-gang unit. Tools/hardware required 2-gang Plastic Faceplate (supplied with B-G2-FP) 2-gang Detent Plate (supplied with B-G2-FP) (2) Single Gang Keypads (supplied separately), which includes: Buttons (2) Dividers (4) 1 in. flathead phillips screws Cresnet network cable (supplied separately) Phillips screwdriver (supplied by other) After the Cresnet network wiring has been installed and verified, use the following procedure to install the keypads in a standard, 2-gang electrical box (refer to illustrations on pages 7 and 8). Installation Guide - DOC. 8182 2 and 3 Gang Faceplates: B-G2-FP & B-G3-FP · 5 2 and 3 Gang Faceplates 1. 3. Crestron B-G2-FP & B-G3-FP Turn Cresnet system power OFF. Connect the Cresnet cable to the keypads' Cresnet ports and the other ends to the control system. Attach the two keypad button assemblies to the detent plate using the (4) 3/16 in. flathead screws (supplied with keypads). CAUTION: Excess wire that is pinched between the keypad and electrical box could short out. Make sure that all excess wire is completely inside the electrical box and not between the box and the keypad. Make sure 2-gang unit is oriented as marked with keypads' arrows at top, and place unit in the electrical box. Attach buttons with LED window oriented upward to match each LED indicator. Attach dividers making sure dividers' interlock tabs are oriented correctly (refer to the "Interlock Tabs Example" illustration on page 8). Attach faceplate (orient with arrow up, make sure it snaps into place). 8. NOTE: If you are installing a metal 2-gang faceplate, carefully clean plastic faceplate mentioned in step 8, (leave no dust or debris on faceplate), observe alignment, remove adhesive liners from inner surface of metal faceplate and mount over 2-gang plastic faceplate. Turn Cresnet system power ON. 6 · 2 and 3 Gang Faceplates: B-G2-FP & B-G3-FP Installation Guide - DOC. 8182 Crestron B-G2-FP & B-G3-FP Installation View 2-Gang Button assembly 2 and 3 Gang Faceplates 2 gang detent 3/16 in. panhead Two gang detent with button assemblies Installation Guide - DOC. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N. J. , or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. [. . . ]