User manual CRESTRON AADS AADS-XM

[. . . ] Crestron AdagioTM AADS Adagio Audio Distribution System Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions · · · · · · · · Read these instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or groundingtype plug. [. . . ] Press SELECT to store the maximum volume setting and to return to the Room Setup menu. · Adjust the Startup Volume The startup volume establishes the volume level setting for a room when a room is turned on. The startup volume settings of each room can be adjusted independently. Press down on the selection control until Start Volume is displayed and press SELECT to open the Startup Volume control. The current startup volume setting is displayed. 32 · Audio Distribution System: Adagio AADS Operations Guide ­ DOC. 6458 Crestron AdagioTM AADS Audio Distribution System Startup Volume Control SOURCE ROOM PRESET MENU BKLT Room 6 Start Volume 50% SCHED DISPLAY MORE · Adjust the maximum volume with the selection control. Press up to raise the maximum volume or press down to lower the maximum volume. Press SELECT to store the startup volume setting and to return to the Room Setup menu. · Set Mono or Stereo Mode The audio sent to the speakers in each room can be set for either stereo or mono. When set to stereo, the audio signal is separated into left and right channels for distribution to left and right speakers. When set to mono, the audio signal is combined into one signal for use in larger rooms where stereo separation is not practical. Press down on the selection control until Stereo/Mono is displayed and press SELECT to open the Stereo/Mono control. The selected mode is displayed on the LCD. Stereo/Mono Control SOURCE ROOM PRESET MENU BKLT Room 6 Stereo SCHED DISPLAY MORE · · · To select stereo, press the selection control down to display Stereo and press SELECT. To select mono, press the selection control up to display Mono and press SELECT. To cancel and return to the Room Setup menu, press the MENU button. Configure Presets Presets can be created to group speakers in adjacent rooms with a specified source, or switch into a whole-house "party" mode, by letting the user link a source with any number of rooms. Changing the source in any one room changes the source in all of the rooms in the preset. Edit a Preset To edit a preset: · Press and hold the PRESET button for approximately five seconds to view the Edit Presets control shown in the following diagram. Operations Guide ­ DOC. 6458 Audio Distribution System: Adagio AADS · 33 Audio Distribution System Edit Presets Control SOURCE ROOM PRESET MENU Crestron AdagioTM AADS BKLT Edit Presets 1: Party SCHED DISPLAY MORE · · To configure a preset, press up or down on the selection control to display the preset to be configured and press SELECT. To add rooms to the preset, press the corresponding room buttons on the AADS or AAE (if connected). To select a source for the preset: Press up or down on the selection control until the word Source is displayed and press SELECT. Select Preset Source SOURCE ROOM PRESET MENU BKLT · Edit Preset 1 Source SCHED DISPLAY MORE Press up or down on the selection control until the desired source is displayed and press SELECT. · To change the name of the preset: Press up or down on the selection control until the word Name is displayed and press SELECT. Press the selection control up or down to display any of the built-in preset names and press the SELECT button. Select Preset Name SOURCE ROOM PRESET MENU BKLT Enter Preset 1 Name [Party] SCHED DISPLAY MORE To enter a custom name, press the selection control up until [Custom Name] is displayed and press the SELECT button. 34 · Audio Distribution System: Adagio AADS Operations Guide ­ DOC. 6458 Crestron AdagioTM AADS Edit Preset Name SOURCE ROOM PRESET MENU Audio Distribution System BKLT Enter Preset 1 Name Partya SCHED DISPLAY MORE Move the cursor position by pressing the selection control up or down. Select letters (upper and lower-case), numbers, or other characters by pressing the volume control up or down until the desired letter, number, or other character is displayed on the LCD. [. . . ] Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. [. . . ]