User manual CRESTON SWAMP-24X8 11-10

[. . . ] Crestron SWAMP(I)-24X8 SonnexTM Multiroom Audio System Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions · · · · · · · · · Read these instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or groundingtype plug. [. . . ] When enabled, the Speaker Protect function will prevent the delivered power from exceeding the speaker's power rating. · · · · 26 · SonnexTM Multiroom Audio System: SWAMP(I)-24X8 Operations & Installation Guide ­ DOC. 7049A Crestron SWAMP(I)-24X8 · · SonnexTM Multiroom Audio System Impedance: Specifies the impedance of a speaker connected to a selected zone. NOTE: As speaker ratings vary greatly across manufacturers, there is no guarantee that Sonnex Speaker Protect will protect against speaker damage in all situations. · · Crestron DRC: Enables or disables the Crestron Dynamic Range Control function Global EQ: Sets the same EQ preset for all zones in the system. Setting this option will override any EQ selection that was previously set for an individual zone. Enter Installer Mode as described in "Enter Installer Mode" on page 25. Enter the Zone Setup menu as described in "Enter/Exit Zone Setup Menu" above. The EQ controls will be displayed. EQ Controls ­ Select Zone Enter/Exit Zone Setup Menu To enter the Zone Setup menu: 1. 2. 3. Press the or buttons to display the zone to be controlled and press ENTER. 2. Press the or buttons to display the setting to be applied and press ENTER. Enter the Zone Setup menu as described in "Enter/Exit Zone Setup Menu" above. The Bass controls will be displayed. SonnexTM Multiroom Audio System: SWAMP(I)-24X8 · 27 To set a zone's bass setting: Operations Guide ­ DOC. 7049A SonnexTM Multiroom Audio System Bass Controls ­ Select Zone Crestron SWAMP(I)-24X8 3. Press the or buttons to display the zone to be controlled and press ENTER. 2. Press the or buttons to display the setting to be applied and press ENTER. Enter the Zone Setup menu as described in "Enter/Exit Zone Setup Menu" on page 27. The Treble controls will be displayed. Treble Controls ­ Select Zone To set a zone's treble setting: 3. Press the or buttons to display the zone to be controlled and press ENTER. Set Loudness 1. Press the or buttons to display the setting to be applied and press ENTER. Enter the Zone Setup menu as described in "Enter/Exit Zone Setup Menu" on page 27. To set a zone's loudness setting: 28 · SonnexTM Multiroom Audio System: SWAMP(I)-24X8 Operations & Installation Guide ­ DOC. 7049A Crestron SWAMP(I)-24X8 2. SonnexTM Multiroom Audio System Press the or buttons to display Loudness and press ENTER. The Loudness controls will be displayed. Loudness Controls ­ Select Zone 3. Press the or buttons to display the zone to be controlled and press ENTER. 2. Press the or buttons to display the setting to be applied and press ENTER. Enter the Zone Setup menu as described in "Enter/Exit Zone Setup Menu" on page 27. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number and return address. Products may be returned for credit, exchange or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]