User manual CRAFTSMAN 315-277140

[. . . ] OBSERVE ALL NORMAL SAFETY PRECAUTIONS RELATED TO AVOIDING ELECTRICAL SHOCK. WARNING: DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ THOROUGHLY AND UNDERSfAND COMPLETELY ALL INSTRUCTIONS, SAFETY RULES, ETC. FAILURE TO COMPLY CAN RESULT IN ACCIDENTS INVOLVING FIRE, ELECTRIC SHOCK, OR SERIOUS PERSONAL INJURY. SAVE OWNERS MANUAL AND REVIEW FREQUENTLY FOR CONTINUING SAFE OPERATION, AND INSTRUCTING OTHERS WHO MAY USE THIS TOOL. [. . . ] A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this instruction manual. Do not operate tool while under the influence of drugs, alcohol, or any medication. To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). If it still does not fit, contact a qualified electrician to install the proper outlet. Review them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. Page 3 FEATURES Your sander is suitable for sanding with coarse, medium, and fine grit sanding discs. BEFORE ATTEMPTING TO USE YOUR SANDER, FAMILIARIZE YOURSELF WITH ALL OPERATING FEATURES AND SAFETY REQUIREMENTS. WARNING: IF ANY PARTS ARE MISSING DO NOT OPERATE YOUR SANDER UNTIL THE MISSING PARTS ARE REPLACED. FAILURE TO DO SO COULD RESULT IN POSSIBLE SERIOUS PERSONAL INJURY ELECTRICAL CONNECTION Your sander has a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). A voltage drop of more than 10 pelcentwill cause a loss of power and overheating. If your tool does not operate when plugged into an outlet, double·check the power supply. WARNING: DO NOT ALLOW FAMILIARITY WITH YOUR SANDER TO MAKE YOU CARELESS. REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY. SWITCH See Figure 1. This tool is equipped with a simple switch control. To turn sander "ON", depress the switch button as shown in Figure 1. Depress the switch button in the opposite direction to turn your sander "OFF". BE SURE SANDER SWITCH IS I~ "OFF" POSITION BEFORE CONNECTING TO POWER SUPPLY SOURCE. SANDING DISC Fig. 1 "Mi@· The operation of any sander can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with sideshieldsand a full face shield when needed. We recommend Wide Vision Safety Maskfor use over eyeglasses or standard safety glasses with side shields, available at Sears Retail Stores. Page 4 OPERATION WARNING: YOUR SANDER SHOULD NEVER BE CONNECTED TO POWER SUPPLY WHEN YOU ARE ASSEMBLING PARTS, MAKING ADJUSTMENTS, ASSEMBLING OR REPLACING SANDING DISC, CLEANING, OR WHEN NOT IN USE. DISCONNECTING SANDER WILL PREVENT ACCIDENTAL STARTING THAT COULD CAUSE SERIOUS PERSONAL INJURY APPLICATIONS (USE ONLY FOR THE PURPOSES LISTED BELOW) 1. Removing rustfrom and sanding steel surfaces. SANDING DISC SELECTION Selecting the correct size grit and type sanding disc is an extremely important step in achieving a high quality sanded finish. Aluminum oxide, silicon carbide, and other synthetic abrasives are best for power sanding. [. . . ] RANDOM ORBIT SANDER MODEL NUMBER 315. 277140 C(1 10~1 ~2 ~-4 I -5 62~lb6 0--7 La 9 NOTE: "A"· The assembly shown represents an important part of the Double Insulatsd System. To avoid the possibility of alteration or damage to the System, service should be performed by your nearest Sears Repair Center. Contact your nearest Sears Retail Store for Service Center information. Page 10 CRAFTSMAN 4-1/2 INCH INDUSTRIAL PALM GRIP RANDOM ORBIT SANDER MODEL NUMBER 315. 277140 f The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your SANDER or when ordering repair parts. I SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Key No. [. . . ]