User manual COMPAQ W220Q

[. . . ] W220q LCD Monitor User's Guide The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] Use the Menu button (C) to adjust the display settings to your personal preferences: · · · · · Set up the monitor, attach the cables, and adjust the tilt as described in the Setup section above. Set the resolution (Setting the Optimal Resolution) and adjust the volume (Adjusting the Volume). Adjust the onscreen display (OSD) settings (Adjusting On-screen Display Settings). 11 External Controls A B C D E F G ­ (minus) button + (plus) button Menu button Mute button Auto button Power button Power LED Navigates backward through the OSD menu and decreases adjustment levels. Navigates forward through the OSD menu and increases adjustment levels. Fully powered = green Sleep mode = amber Sleep timer mode = flashing amber See Technical Support FAQs for more information. 12 Settings Setting the Optimal Resolution The recommended resolution for this monitor is 1680 x 1050. To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the following: 1 Click the Windows Start Button®, and then click Control Panel. 2 Under Appearance and Personalization, click Adjust Screen Resolution. 3 Set the resolution slide bar to 1680 x 1050. NOTE: If 1680 x 1050 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions. Adjusting the Volume While the monitor is turned on but the OSD menu is inactive, press the volume increase and decrease (plus and minus) buttons to adjust volume to the desired level. Download and install the driver and software files using the instructions in the download pages. Using the Auto-Adjustment Function Press the Auto button to optimize the screen performance for VGA (analog). If your monitor is using VGA (analog) input, auto-adjustment can correct the following image quality conditions: · · · · · Fuzzy or unclear focus Ghosting, streaking, or shadowing effects Faint vertical bars Thin, horizontal scrolling lines An off-center picture 17 Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Problem & Question Power LED is not on. Possible Solutions · Make sure the Power button is on and the power cord is properly connected to a grounded power outlet and to the monitor. · In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer and video card. · Check the monitor's video cable and make sure none of the pins are bent. · Make sure the HP monitor drivers are installed (HP monitor drivers are available at: http://www. hp. com/support) Picture is fuzzy and has ghosting shadowing problem. · Adjust the contrast and brightness controls. · Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly into the video card output connector on the back of your computer. · For VGA input, the auto-adjustment function may fix this problem. Picture bounces, flickers or wave pattern is present in the picture. · Move electrical devices that may cause electrical interference as far away from the monitor as possible. · Use the maximum refresh rate your monitor is capable of at the resolution you are using. Monitor is stuck in "Active Off-Mode. " · The computer power switch should be in the on position. · Make sure the monitor's video cable is properly connected to the computer. · Inspect the monitor's video cable and make sure none of the pins are bent. [. . . ] We expect that, over time, the industry will continue to improve its ability to produce displays with fewer cosmetic imperfections, and we will adjust guidelines as improvements are made. For more information about your W220q Monitor, refer to the HP Web site at: http://www. hp. com/support Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]