User manual COMPAQ W1858

[. . . ] User's Guide w1858 w2228h w2338h w2348h w2448h/hc w2558hc The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] If you adjust the Quick View, Brightness, Contrast, or sRGB functions in the OSD, the ambient light sensor will automatically be disabled. Clock Minimizes any vertical bars or strips visible on the screen background. Adjusting the Clock will also change the horizontal screen image (VGA Input only). This adjustment allows you to remove any horizontal noise, and clear or sharpen the image of characters (VGA Input only). Clock Phase User's Guide 4­5 Operating the Monitor Icon Main Menu Options Color Submenu Options Description (Continued) Selects the screen color. The factory default is 6500 K or Custom Color, depending on the model. 9300 K 6500 K Custom Color Changes to slightly blueish white. Selects and adjusts your own color scales: R -- Sets your own red color levels. B -- Sets your own blue color levels. sRGB Quick View Movie Photo Gaming Text Custom Language Management Volume OSD Control Sets your screen colors to adapt to the color standards used in the image technology industry. Settings saved when user adjusts the Brightness, Contrast, or Color in one of the Quick View options. Horizontal OSD Position -- Changes the viewing position of the OSD menu to the left or right area of the screen. Vertical OSD Position -- Changes the viewing position of the OSD menu to the top or bottom area of the screen. OSD Transparency -- Adjust to view the background information through the OSD. OSD Timeout -- Sets the time in seconds that the OSD is visible after the last button is pressed. The factory default is 30 seconds. Power Saver Enables the power saving feature (see "Power-Saver Feature" in this chapter). Select: On Off The factory default is On. Mode Display Displays the resolution, refresh rate, and frequency information on the screen each time the OSD Main Menu is accessed. Select: On Off The factory default is On or Off, depending on the model. 4­6 User's Guide Operating the Monitor Icon Main Menu Options Management (continued) Submenu Options Power-On Status Display Description (Continued) Displays the operating status of the monitor each time the monitor is powered on. Select the location to which to display the status: Top Middle Bottom Off The factory default is Top or Off, depending on the model. DDC/CI Support Allows the computer to control some OSD menu features such as brightness, contrast, and color temperature. Set to: On Off The factory default is On. Bezel Power LED Sleep Timer Turns the light (LED) in the power button On and Off. Provides the timer-adjustment menu options: Set Current Time -- Sets the current time in hours and minutes. Set Sleep Time -- Sets the time you want to place the monitor in sleep mode. Set on Time -- Sets the time you want the monitor to wake up from sleep mode. Timer -- Sets the Sleep Timer feature On or Off; the default setting is Off. Sleep Now -- Immediately sets the monitor to enter sleep mode. Default Video Input Selects the default video input signal when the monitor is connected to two active and valid video sources. Selects and displays important information about the monitor. Information Current Settings Recommended Settings Serial Number Version Backlight Hours Service Support Factory Reset Provides the current input video mode. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC rules and regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. [. . . ]