User manual COMPAQ W17E

[. . . ] The sections are as follows: · · · · · · · · Safety and Maintenance Guidelines Setup Using the Monitor Installing Drivers and Using the Auto-Adjustment Feature Technical Support FAQs Specifications LCD Monitor Quality and Pixel Policy Agency Regulatory Notices Notational Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your monitor. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data, and tells you how to avoid the problem. WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority. Back to Contents Page Safety and Maintenance Guidelines Important Safety Information · Safety Precautions · Maintenance Guidelines · Cleaning the Monitor Important Safety Information The power cord is designed for use with your monitor. To use a different cord, use only a power source and connection compatible with this monitor. [. . . ] To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the following: 1 Click the Windows Start Button , and then click Control Panel. 2 Under Appearance and Personalization, click Adjust Screen Resolution. 3 Set the resolution slide bar to 1440 by 900. NOTE: If 1440 by 900 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions. Adjusting the Volume Press the front monitor panel volume increase and decrease buttons to adjust volume to the desired level. Volume cannot be adjusted through the OSD menu. Locking the OSD To lock the OSD (onscreen display), press and hold the Menu button while the monitor is off, then press the power button to turn the monitor on. Download and install the driver and software files using the instructions in the download pages. Using the Auto-Adjustment Function Press the Auto button to optimize the screen performance for VGA (analog). Auto-adjustment can correct the following image quality conditions: · · · · · Fuzzy or unclear focus Ghosting, streaking, or shadowing effects Faint vertical bars Thin, horizontal scrolling lines An off-center picture Back to Contents Page Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Technical Support FAQs (Frequently Asked Questions) Problem & Question Power LED is not on No Plug & Play Possible Solutions · Make sure the Power button is on and the power cord is properly connected to a grounded power outlet and to the monitor. · In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer and video card. · Check the monitor's video cable and make sure none of the pins are bent. · Make sure the HP monitor drivers are installed (HP monitor drivers are available at: http://www. hp. com/support). Picture is fuzzy and has ghosting shadowing problem · Adjust the contrast and brightness controls. · Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly into the video card output connector on the back of your computer. · The Auto-adjustment function may fix this problem. Picture bounces, flickers or wave pattern is present in the picture · Move electrical devices that may cause electrical interference as far away from the monitor as possible. · Use the maximum refresh rate your monitor is capable of at the resolution you are using. Monitor is stuck in "Active Off-Mode" · The computer power switch should be in the on position. · Make sure the monitor's video cable is properly connected to the computer. · Inspect the monitor's video cable and make sure none of the pins are bent. · Make sure your computer is operational by hitting the Caps Lock key on the keyboard while observing the Caps Lock LED. The LED should either turn on or off after hitting the Caps Lock key. Problem & Question Missing one of the primary colors (red, green, or blue) Possible Solutions (continued) · Inspect the monitor's video cable and make sure that none of the pins are bent. · Make sure the monitor's video cable is properly connected to the computer. Screen image is not centered or sized properly Picture has color defects (white does not look white) Unable to set the monitor to the optimal resolution · Adjust horizontal and vertical screen position. · Make sure that the graphics card supports the optimal resolution (1440 x 900). · Make sure that the latest supported driver is installed for the graphics card. For HP and Compaq systems, you can download the latest graphics driver for your system from: http://www. hp. com/support For other systems, refer to the Web site for your graphics card. Back to Contents Page Specifications General· LCD Panel (17") · Resolution · Preset Display Modes · Physical Characteristics · Environmental · Power Cord Set Requirements · VGA Connector Pin Assignments · Plug and Play DDC2B Feature All specifications represent the typical specifications provided by HP's component manufacturers; actual performance may vary either higher or lower. General Model number w17e / W17q LCD Panel (17") Driving system Size Video Separate sync. Display color Dot clock Pixel Pitch Face treatment Viewable angle TFT Active Matrix Color LCD 431. 8 mm (17" diagonal) R, G, B Analog Interface H/V TTL & TMDS 262, 000 colors 135 MHz maximum 0. 255 mm (H) x 0. 255 mm (V) Antiglare polarizer with hard coating 140° (H), 130° (V) Resolution Horizontal scan range Horizontal scan size (Maximum) Vertical scan range Vertical scan size (Maximum) Optimal preset resolution Highest preset resolution Highest addressable resolution Plug & Play Input Connectors Input Video Signal Power Source 30 kHz to 83 kHz 367. 2 mm 55 Hz to 75 Hz 229. 5 mm 1440 x 900 at 60 Hz 1440 x 900 at 75 Hz 1440 x 900 at 75 Hz VESA DDC2B D-Sub VGA 15-pin and audio jack Analog: 0. 7Vp-p (standard), 75 OHM 100~240V , 47~63 Hz Preset Display Modes Standard Dos-mode VGA VGA VGA VGA SVGA SVGA SVGA SVGA SVGA XGA XGA XGA SXGA WXGA WXGA Resolution 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1440 x 900 1440 x 900 Horizontal Frequency (kHz) 31 31 35 38 38 35 38 48 47 50 48 56 60 68 56 71 Vertical Frequency (Hz) 70 60 67 73 75 56 60 72 75 75 60 70 75 75 60 75 Physical Characteristics Connector Types Signal Cable Type Dimensions & Weight: Height (with base) Width Depth Weight (monitor only) Weight (with packaging) 13. 1 inches (332. 4 mm) 15. 8 inches (400. 4 mm) 8. 3 inches (211 mm) 7. 17 lb (3. 25 Kg) 10. 67 lb (4. 84 Kg) 15-pin Mini D-Sub VGA Detachable Environmental Temperature: Operating Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non-Operating 0~3, 658 m (0~12, 000 ft) 0~12, 192 m (0~40, 000 ft) 20% to 80% (non-condensing) 5% to 90% (non-condensing) 5°C to +35°C ­20°C to +60°C Power Cord Set Requirements The monitor power supply is provided with automatic line switching (ALS). [. . . ] The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Japanese Notice Japanese Power Cord Notice Japanese Material Content Declaration A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit www. hp. com/go/jisc0950 Korean Notice Materials Disposal This HP product contains Mercury in the fluorescent lamp in the display LCD that might require special handling at end-of-life. Disposal of this material can be regulated because of environmental considerations. [. . . ]