User manual COMPAQ P930 MONITOR

[. . . ] User's Guide P930 Monitor Document Part Number: 305776-001 September 2002 © 2002 Hewlett-Packard Company Microsoft, MS-DOS, Windows, Windows NT are trademarks of Microsoft Corporation in the U. S. All other product names mentioned herein may be trademarks of their respective companies. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. The information in this document is provided "as is" without warranty of any kind, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, and is subject to change without notice. [. . . ] · Select Sidepin to adjust the sidepin corner correction when the sides of the display are bowed in or bowed out, or when the top or bottom of the display is too large or small. · Select the Pinbalance Corner correction when the sides of the display are bowed in or bowed out, or when the top or bottom of the display is too large or small. User's Guide 4­11 Operating the Monitor Menu Color Function Continued Use to select Color 1, Color 2, or Color 3 to change the color temperature and adjust individual red, green and blue color control. Color temperature is a measure of the "warmth" of the image colors. The available range is between 5000 to 9300K. If you select recall to reset your monitor setting, the Color settings will not reset. 4­12 User's Guide Operating the Monitor Menu Screen Function Continued · Select Clear Moire when a moire pattern, which looks like a series of concentric circles or arcs, appears on your screen. · Select Linearity to adjust the settings when the display image is compressed at the left, right or top, bottom. · Select Focus when the image displayed on the screen is not sharp in all areas. · Select Convergence to adjust the horizontal or vertical convergence to properly align the color dots that make up the image. Convergence affects picture clarity. User's Guide 4­13 Operating the Monitor Menu Advanced Function Continued · Select Degauss to remove color impurities caused by magnetic fields. Do not use the degauss feature more than once within a 30 minute period. After using the degauss feature, the monitor may buzz momentarily, the image colors may change and the image will jiggle for a few seconds. · Select Recall to reset the monitor settings to their original levels. If you press Yes to reset the monitor, the position, size, pincushion, trapezoid, parallelogram, pinbalance, rotation, and clear moire settings will be reset. · Select Video Input Level to set the level to 1. 0 V for video cards that use video signals higher than 1. 0 V, which causes the display to be very bright. 4­14 User's Guide Operating the Monitor Menu Menu Function Continued · Select Display Timing to see the frequency (user control mode), the polarity of the operational signals, the default frequency set by the manufacturer, and the resolution level of your monitor. These screens do not allow any changes to the settings. · Select Menu Position to change the position of where the OSD menu appears on your monitor. · Select Menu Duration to set the amount of time the menu will wait before it automatically turns off if no adjustments. · Select Languages to choose from one of ten languages: English, German, French, Italian, Portuguese, Spanish, Swedish, Russian, Polish or Magyar. Some languages may not appear in some regions. The language chosen affects only the language of the OSD. It has no affect on any software running on the computer. User's Guide 4­15 Operating the Monitor Monitor messages Special messages will appear on the monitor screen to identify the following monitor conditions: Video mode not supported - If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator light is still on. This message indicates the monitor is out of scan range or that you need to check the signal cable. No Connection, check signal cable - Indicates the video cable may not be plugged into the computer or the computer may not be turned on. Energy saver feature When the monitor is in its normal operating mode, the monitor uses 120 watts maximum of power and the Power light is green. The reduced power state will be entered into if the monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon detecting the absence of these signals, the monitor screen is blanked and the power light flashes green. When the monitor is in the reduced power state, the monitor will use 3 watts maximum of power. [. . . ] Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy. This product meets the requirements for the TCO'99 scheme which provides for international and environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. [. . . ]