Detailed instructions for use are in the User's Guide.
[. . . ] Maintenance and Service Guide
HP Compaq nx6110/nc6110 and nx6120/nc6120 Notebook PCs
Document Part Number: 373146-001
February 2005
This guide is a troubleshooting reference used for maintaining and servicing the notebook. It provides comprehensive information on identifying notebook features, components, and spare parts; troubleshooting notebook problems; and performing notebook disassembly procedures.
© Copyright 2005 Hewlett-Packard Development Company, L. P. Intel, Pentium, and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. [. . . ] Other grounding equipment recommended for use in preventing electrostatic damage includes: Antistatic tape Antistatic smocks, aprons, and sleeve protectors Conductive bins and other assembly or soldering aids Nonconductive foam Conductive tabletop workstations with ground cords of one megohm resistance Static-dissipative tables or floor mats with hard ties to the ground Field service kits Static awareness labels Material-handling packages Nonconductive plastic bags, tubes, or boxes Metal tote boxes Electrostatic voltage levels and protective materials
Maintenance and Service Guide
47
Removal and Replacement Preliminaries
Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
Table 4-1 Typical Electrostatic Voltage Levels
Relative Humidity Event Walking across carpet Walking across vinyl floor Motions of bench worker Removing DIPS from plastic tube Removing DIPS from vinyl tray Removing DIPS from Styrofoam Removing bubble pack from PCB Packing PCBs in foam-lined box 10% 35, 000 V 12, 000 V 6, 000 V 2, 000 V 11, 500 V 14, 500 V 26, 500 V 21, 000 V 40% 15, 000 V 5, 000 V 800 V 700 V 4, 000 V 5, 000 V 20, 000 V 11, 000 V 55% 7, 500 V 3, 000 V 400 V 400 V 2, 000 V 3, 500 V 7, 000 V 5, 000 V
A product can be degraded by as little as 700 V.
Table 4-2 lists the shielding protection provided by antistatic bags and floor mats.
Table 4-2 Static-Shielding Materials
Material Antistatic plastic Carbon-loaded plastic Metallized laminate Use Bags Floor mats Floor mats Voltage Protection Level 1, 500 V 7, 500 V 5, 000 V
48
Maintenance and Service Guide
5
Removal and Replacement Procedures
This chapter provides removal and replacement procedures. There are 62 screws and screw locks, in 11 different sizes, that must be removed, replaced, or loosened when servicing the notebook. Make special note of each screw and screw lock size and location during removal and replacement. Refer to Appendix C, "Screw Listing" for detailed information on screw and screw lock sizes, locations, and usage.
Maintenance and Service Guide
51
Removal and Replacement Procedures
5. 1 Serial Number
Report the notebook serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the notebook.
Serial Number Location
52
Maintenance and Service Guide
Removal and Replacement Procedures
5. 2 Disassembly Sequence Chart
Use the chart below to determine the section number to be referenced when removing notebook components.
Disassembly Sequence Chart
Section
5. 3
Description
Preparing the notebook for disassembly Battery pack Hard drive
# of Screws Removed
0 2 loosened to remove the hard drive cover 1 loosened to remove the hard drive 6 to disassemble hard drive 0 0 1 loosened to remove the memory module/Mini PCI compartment cover 1 loosened to remove the memory module/Mini PCI compartment cover
5. 4 5. 5 5. 6
Notebook feet Bluetooth board External memory module
5. 7
Mini PCI Communications Card
Å
To prevent an unresponsive system and the display of a warning message, install only a Mini PCI device authorized for use in your notebook by the governmental agency that regulates wireless devices in your country. If you install a device and then receive a warning message, remove the device to restore notebook functionality. 1
5. 8
Optical drive
Maintenance and Service Guide
53
Removal and Replacement Procedures
Disassembly Sequence Chart (Continued)
Section
5. 9 5. 10 5. 11 5. 12 5. 13 5. 14 5. 15 5. 16 5. 17 5. 18 5. 19 5. 20 5. 21 5. 22 5. 23
Description
Keyboard Switch cover LED board Fan Heat sink Processor Modem board Internal memory module RTC battery Display assembly Top cover Speaker Digital media board USB/audio board System board
# of Screws Removed 2 2 4 2 loosened 4 loosened 1 loosened 2 0 0 6 15 4 0 1 1 screw 4 screw locks on HP Compaq nc6110 and nc6120 models 2 screw locks on HP Compaq nx6110 and nx6120 models 2 screw locks
5. 24
Serial connector module
54
Maintenance and Service Guide
Removal and Replacement Procedures
5. 3 Preparing the Notebook for Disassembly
Before you begin any removal or installation procedures: 1. If you are unsure whether the notebook is off or in hibernation, turn the computer on, and then shut it down through the operating system. Disconnect the power cord.
Battery Pack Spare Part Number Information
6-cell, 4. 4-AHr 6-cell, 4. 4-AHr 6-cell, 2. 2-AHr 372772-001 383220-001 364602-001
4. Turn the notebook upside down with the rear panel toward you.
Maintenance and Service Guide
55
Removal and Replacement Procedures
b. Slide the battery pack straight back 3 and remove it.
Removing the Battery Pack
Reverse the above procedure to install the battery pack.
56
Maintenance and Service Guide
Removal and Replacement Procedures
5. Loosen the 2 PM2. 0×4. 0 screws 1 that secure the hard drive cover to the notebook. Lift the left side of the hard drive cover and swing it to the right 2. drive cover is included in the Miscellaneous The hardKit, spare part number 378236-001. Plastics
Removing the Hard Drive Cover
Maintenance and Service Guide
57
Removal and Replacement Procedures
Hard Drive Spare Part Number Information
5400-rpm 80-GB 60-GB 40-GB 380108-001 378215-001 380107-001 4200-rpm 80-GB 60-GB 30-GB 378214-001 378213-001 378211-001
d. Loosen the PM2. 5×13. 0 spring-loaded hard drive retention screw 1. Grasp the mylar tab 2 on the left side of the hard drive and slide the hard drive to the right 3 to disconnect it from the system board. Remove the hard drive from the hard drive bay 4.
Removing the Hard Drive
58
Maintenance and Service Guide
Removal and Replacement Procedures
g. Remove the 2 PM2. 5×4. 0 hard drive frame shoulder screws 1 from each side of the hard drive. Remove the 2 PM2. 5×4. 0 hard drive frame screws 2 from each side of the hard drive. Remove the 2 PM1. 5×3. 5 hard drive frame screws 3 from the front of the hard drive. Remove the hard drive connector 5 from the hard drive.
Removing the Hard Drive Frame and Connector
Reverse the above procedure to install and reassemble the hard drive.
Maintenance and Service Guide
59
Removal and Replacement Procedures
5. 4 Notebook Feet
The notebook feet are adhesive-backed rubber pads. [. . . ] The appliance coupler, flexible cord, and wall plug must bear a "T" mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1. 00 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
B4
Maintenance and Service Guide
C
Screw Listing
This appendix provides specification and reference information for the screws and screw locks used in the notebook. All screws and screw locks listed in this appendix are available in the Screw Kit, spare part number 378235-001.
Maintenance and Service Guide
C1
Screw Listing
Table C-1 Phillips PM2. 0×4. 0 Screw
Head Width 4. 0 mm
mm
Color Black
Qty. [. . . ]