User manual COMPAQ MP1600

[. . . ] Compaq MP1600 Microportable Projector User's Guide Notice The information in this guide is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation. Microsoft, MS-DOS, Windows, Windows NT, and other names of Microsoft products referenced herein are trademarks or registered trademarks of Microsoft Corporation. [. . . ] The on-screen menu is easy to use; just follow the instructions on the screen. Explaining Functions in the On-Screen Menu s Brightness and Contrast--Adjusts the displayed image brightness and contrast ranges from 0 to 100. Position--Fine-tunes the horizontal and vertical positions of the display. Zoom--Magnifies an image up to a factor of 32 on the projection screen. The only adjustment direction allowed is to narrow the top width of the image. Picture--Adjusts the gamma value or degree of contrast of darkness or light for the projected image. Color--Adjusts color balance to compensate for ambient conditions using three submenus: t t t s s s s s 7100°K--The factory default. Saturation--Magnify the color intensity. English 1-19 s Digital Conversion--Improves picture stability of user modes by adjusting: #Clock--Increase/decrease the value to stretch or shrink the image on the screen. #Clock Phase--Increase/decrease the value to minimize video distortion or video jitter. distorted when adjusting the If the projector image becomes continue adjusting the values Clock and Clock Phase values, until the distortion disappears. To restore the factory settings, select Factory Reset in the on-screen menu. s Language--Select display from six languages in their native spelling. Select another language to display all menu functions in that language. Menu Location--Positions the on-screen menu at a convenient location on the projector screen; moves up and down, left and right. Management--Allows the user to control power saver characteristics of the display, or to view the cumulative lamp hours, reset the lamp hour timer, view the unit's serial number, or perform a Master Reset. Factory Reset--Resets the current operating option to its original factory setting. s s s 1-20 English Special On-Screen Messages Special on-screen messages will appear on the projection display to identify the following conditions: s Check Video Cable: Indicates the video cable may not be plugged into the projector or the selected video input is not accurate. Input Signal Out of Range: Indicates the projector is unable to access the appropriate input signal. 2 Inputs Active - Remove One: The projector has two data inputs: one is an analog D-Sub input and the other is a digital DFP input. This message indicates that both inputs are active simultaneously and the user should detach one of them. Going to Standby: Indicates the projector is entering a sleep mode or powering off the lamp. Lamp May Fail Soon, Replacement Suggested: Indicates the lamp is approaching failure. The message will remain on the screen for five seconds or until the on-screen menu Select button is pressed. s s s s English 1-21 Care and Maintenance This section explains how to care for and maintain your Compaq projector during normal everyday use. Protecting the Projector To protect your projector from overheating and other types of damage, follow these suggestions: s Use only a power source and connection appropriate for this projector as indicated on the marking label. Do not overload an electrical outlet, power strip, or convenience receptacle. The overall system load must not exceed 80 percent of the branch circuit rating. If an extension cord or power strip is used, make sure that the cord or strip is rated for the product and that the total ampere ratings of all products plugged into the extension cord or power strip do not exceed 80 percent of the extension cord or strip ampere ratings limit. [. . . ] The power cord set (flexible cord or wall plug) received with the projector meets the requirements for use in the country where you purchased the equipment. Power cord sets must meet the requirements of the country where you use the projector. For more information on power cord set requirements, contact your Compaq authorized dealer, reseller or service provider. General Requirements The requirements listed below are applicable to all countries: 1. The length of the power cord set must be at least 5. 00 feet (1. 5 m) and a maximum of 10 feet (3. 0 m). [. . . ]