User manual COMPAQ JETDIRECT PN1050 ADMINISTRATOR GUIDE REV 1

[. . . ] HP Jetdirect pn1050 Network Projector Manager Administrator's Guide © Copyright 2005 Hewlett-Packard Development Company, L. P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained in this document is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. [. . . ] The name must start with a letter and can end in a letter or number, up to 32 ASCII characters. The default name is NPIxxxxxx, where xxxxxx is the last six digits of the LAN hardware (MAC) address. Use this field to manually assign the Internet Protocol address on the HP Jetdirect projector server. The IP address is a four byte (32-bit) address in the form "n. n. n. n", where `n' is a number from 0 to 255. For more information on IP addresses, see Appendix A. IP Address Subnet Mask If subnetting is used, use this field to manually assign a subnet mask. A subnet mask is a 32-bit number that, when applied to an IP address, determines which bits specify the network and subnet, and which bits uniquely specify the node. For more information on subnet masks, see Appendix A. ENWW Using the Embedded Web Server 53 Table 4. 3 Item TCP/IP Settings (2 of 3) Description Identifies the IP address of a router or computer that is used to connect to other networks or subnetworks. Specifies the name of the Domain Name System (DNS) domain that the HP Jetdirect projector server resides in (for example, support. hp. com). It does not include the host name; it is not the Fully Qualified Domain Name (such as projector1. support. hp. com). Specifies the IP address of the primary Windows Internet Naming Service (WINS) server. The WINS server provides IP address and name resolution services for network computers and devices. Specifies the IP Address to be used for WINS if the primary WINS Server is unavailable. Specifies the IP address of a host computer that is configured to receive syslog messages from the HP Jetdirect projector server. For more information, see Appendix A. Default Gateway Domain Name Primary WINS Server Secondary WINS Server Syslog Server Syslog Maximum Messages Specifies the maximum number of syslog messages that can be sent by the HP Jetdirect projector server on a per-minute basis. Controls the filtering of syslog messages that are sent to the syslog server. The filter range is 0 to 8, with 0 being the most specific and 8 being the most general. Only messages that are lower than the filter level specified (that is, higher in priority) are reported. Specifies the number of seconds that an idle connection is allowed to remain open. If set to 0, the timeout is disabled and TCP/IP connections will remain open until closed by the device at the other end of the network (for example, a workstation). Syslog Priority Idle Timeout ENWW Using the Embedded Web Server 54 Table 4. 3 Item TTL/SLP TCP/IP Settings (3 of 3) Description Specifies the IP multicast Time To Live (TTL) discovery setting for Service Location Protocol (SLP) packets. The default value is 4 hops (the number of routers from the local network). For projector servers configured for Auto IP (link-local) addresses, this field will be ignored. TTL on outbound packets will always be set to 255 and limited to the link-local network. System Contact Identifies a person who is assigned to administer or service this device. [. . . ] Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. [. . . ]