User manual COMPAQ F2304

[. . . ] User's Guide HP f2304 High Definition 23" LCD Monitor The information in this document is subject to change without notice. Hewlett-Packard® Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. HP shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO ANY MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT OR SERVICE TO YOU. [. . . ] If additional improvement is desired, select the Auto button on the front bezel. For more precise adjustments, use the adjustment pattern provided on the CD-ROM, and adjust the clock and phase settings (accessed from the OSD menu) as described in the following section. User's Guide 4­9 Operating the Monitor Enhancing the Video Function The monitor includes a zoom feature that allows you to adjust the viewable image to full screen display. It enhances video performance by changing the screen's aspect ratio, the ratio of the picture's width to its height, to get 4 to 3 (standard broadcast) and 16 to 9 (widescreen) formats. The zoom feature is available when the signal input selection is set to super video or component video. Press the Input button on the front panel of the monitor to select one of the following video sources: S-video or Component Video. Press the Menu button on the front panel of the monitor to launch the On Screen Display (OSD) Main Menu. In the Image Zoom menu, use the OSD up and down buttons on the front panel to select and highlight the desired zoom setting: Zoom Off -- turns off the Image Zoom feature and defaults to the 1:1 format. Zoom On 1 -- optimizes the image for 4:3 format sources such as standard broadcast formats and the full screen DVD format. Zoom On 2 -- optimizes the image for 16:9 format sources such as widescreen broadcast and DVD format. 4­10 User's Guide Operating the Monitor DVD wide may provide formats other Some16:9. Whenscreen modesblack video borders may than this occurs, remain visible above and below the displayed image when Zoom On 2 is active. When the desired zoom setting is highlighted, press the Menu button to confirm the selection. Press the Menu button and select Exit to close the Main Menu. Optimizing Digital Conversion This monitor contains advanced circuitry that allows the flat panel screen to function like a standard monitor. Two controls in the OSD can be adjusted to improve image performance: Clock and Clock Phase. Use these controls only when the auto adjust function does not provide a satisfactory image. The Clock must first be set correctly since the Clock Phase settings are dependent on the main Clock setting. Clock -- Increase/decrease the value to minimize any vertical bars or stripes visible on the screen background. Clock Phase -- Increase/decrease the value to minimize video distortion or video jitter. using the controls, you will obtain Whenthe adjustment pattern provided on the best results by using the CD-ROM. User's Guide 4­11 Operating the Monitor the Clock and Clock Phase values, if the When adjustingbecome distorted, continue adjusting the monitor images values until the distortion disappears. To restore the factory settings, select Yes from the Factory Reset menu in the OSD. Using Video Connectors The monitor includes the following video connectors for input from external video sources such as DVD players, VHS recorders, and external television tuners: S-video with composite video adapter included Component video The monitor is compatible with NTSC, PAL, and SECAM video standards. Additionally, the component video connectors are capable of supporting the 480-line progressive (480p), the 720-line progressive (720p), and the 1080-line interlaced (1080i) High Definition Video modes when connected to an external HD video decoder. Composite to S-video Adapter A Composite to S-video adapter is included with your monitor. Use the following steps to connect the adapter and improve the display quality: 1. Connect the video source composite connector into the Composite to S-video adapter. Turn on the monitor. 4­12 User's Guide Operating the Monitor 4. If the display becomes distorted, press and hold the PIP button for at least 5 seconds until the display is corrected. whenever Repeat step 5 Function is the Input button is pressed, or the Factory Reset activated. User's Guide 4­13 Operating the Monitor 4­14 User's Guide 5 Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Screen is blank or the No Input Signal message is displayed. Possible Cause Power cord is disconnected. Solution Connect the power cord. Monitor power switch is turned off. [. . . ] The energy requirements include a demand that the computer and/or monitor, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Below, you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 E-mail (Internet): development@tco. se Current information regarding TCO `99 approved and labeled products may also be obtained over the Internet, using the address: http://www. tco-info. com/ C­2 User's Guide TCO `99 Requirements Environmental requirements Flame retardants: Flame retardants are present in printed circuit boards, cables, wires, casings and housings. [. . . ]