User manual COMPAQ CD-WRITER PLUS

[. . . ] HP CD-Writer Plus User's Guide English English Copyright 1999. Hewlett-Packard is a registered trademark of the Hewlett-Packard Company. Names of products mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective company. 2 Laser Safety This unit employs a laser. Do not remove the cover or attempt to service this device due to the possibility of eye damage. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure. Contains: Class 1 Laser Product Innehåller: Klass 1 Laserapparat Sisältää: Luokan 1 Laserlaite Enhält: Klasse 1 Laser-Produkt DANGER: INVISIBLE LASER RADIATION WHEN OPEN. [. . . ] WARNING: If you are just performing a test of your Disaster Recovery Set, the test is now complete. Please remove any diskettes and CDs from your drive(s) and restart your computer. The following message should appear: Select the volume that you wish to recover. Drive C: [Volume C Name] Drive D: [Volume D Name] NOTE: If you have only one drive, it will be automatically selected for recovery and this screen will not be displayed. Select the volume that you wish to recover by highlighting the volume using the Up and Down arrow keys, then pressing Enter. You will then be asked to confirm your selections before recovering your information. Press Enter to confirm your selections, or press Esc to return to the previous screen(s) and make a different selection. NOTE: If Disaster Recovery CD #1 is not in your HP CD-Writer Plus, you will be prompted to insert it at this time. The recovery process will take some time to complete, depending upon the amount of data you are recovering. You will be prompted to insert the CDs in the order they were created. Once the volume has been recovered, a summary of the process will be displayed. If there is more than one volume to be recovered, you may select it at this time. Recovering Your Data 25 After recovering the volume(s), you may wish to view the REPORT. TXT file which contains a text summary of the files that could not be recovered. If you wish to view this file, you must first exit the program by pressing Esc twice, then type EDIT REPORT. TXT. For more information on files that could not be recovered, see "Files Not Recovered" on page 19. Remove any diskettes and CDs from your drive(s) and restart your computer. NOTE: It may be necessary to restart your computer more than once if any hardware in your system has changed since your DR Set was created. For Windows NT The Disaster Recovery process for Windows NT begins with a minimal install of the Windows NT Workstation, performed from the Disaster Recovery Set. HP Disaster Recovery screens will display messages instructing you when to insert the diskettes and CD(s) from your Disaster Recovery Set. Once the Setup portion of the minimal install has been completed, the Disaster Recovery Wizard will appear and guide you through the rest of the recovery process. For example, if the problem appears to be associated with the Windows operating system, such as a corrupt registry, try to recover by following the steps outlined in your Microsoft Windows User's Manual before attempting the following procedures. If you have determined that a harddrive failure has occurred, proceed to Step 2. In order to recover all of your information, HP Disaster Recovery must have at least as much hard disk space as existed before the drive failure. Insert the Windows NT Workstation Setup Boot Disk (diskette #1 of the DR Set) into into the 3. 5" floppy drive from which your computer boots, and restart your computer. [. . . ] The version number appears below Microsoft Windows 98, and the amount of memory installed is displayed in the lower part of the screen. Example: 4. 10. 1998 and 128. 0 MB RAM In Windows NT (while signed on as Administrator), from the Start menu on the task bar, select Programs, Administrative Tools (Common), and Windows NT Diagnostics. Select the Version tab and write down the version number and service pack number; for example: 4. 00. 1381 and Service Pack 3. Then select the Memory tab and write down the amount of memory listed under Physical Memory - Total; for example: 32 MB RAM Other CD-ROM or DVD-ROM drives In Windows 95 and Windows 98, from the Start menu on the taskbar, select Settings and then Control Panel. [. . . ]