User manual COMET LABS WN591

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. Changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Shielded interface cables must be used in order to comply with emission limits. 1 This EUT is incompliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95. 1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION: 1. [. . . ] Choose the appropriate of installation, according to your needs (Application, Drivers) If you want to set the path of your choice, select "Browse" and then "Next". The installation will be completed after reboot. Insert your WLAN USB adapter. The "Add New Hardware Wizard" automatically loads the Drivers. Refer to sections 3 for more details on the installation and configuration under Microsoft Windows® 98SE/Me/2000/XP respectively. Section 4 gives detailed instructions on how to use the Configuration Utility. WN591 Mini USB Adapter WN591 Mini USB Adapter Copyright© 2004 Comet Labs V1. 0 WN591 Mini USB Adapter Welcome to the InstallShield Wizard for WN591 Mini USB Adapter WN591 Mini USB Adapter The InstallShield ® Wizard will install WN591 Mini USB Adapter on your computer. To continue, click Next. 5 3 Installation Procedures Under MS Windows The procedures described in this section to install and configure the Wireless LAN USB Adapter under MS Windows 98SE/Me/2000/XP. 3. 1 Installing the Application and Drivers under Windows 98SE/Me/2000/XP Please do not plug your USB adapter until the Application setup has been completed. The setup procedure described below installs both the drivers and the Configuration & Monitor Utility. Insert the Driver CD to your CD-ROM, the following window will pop up and Click "Install/Uninstall software" button to install. (If the following window doesn't pop up, click the Start button at the Taskbar and then select Run. Enter E:\autorun. exe if E is your CD-drive. ) WN591 Mini USB Adapter Copyright© 2004 Comet Labs V1. 0 6 2. Follow the installation instructions from the InstallShield Wizard by pressing the "Next" button. WN591 Mini USB Adapter Welcome to the InstallShield Wizard for WN591 Mini USB Adapter The InstallShieldR Wizard will install WN591 Mini USB Adapter on your computer. To continue, click Next. 3. The installer will install the needed files to a folder named "C:\Program Files\Wireless LAN Series\WN591 Mini USB Adapter". If you want to change this, Click"Browse" and select a folder. Click "Next" to continue. Setup will install WN591 Mini USB Adapter in the following folder. To install to a different folder, click Browse and select another folder. C:\Program Files\Wireless LAN Series\WN591 Mini USB Adapter 7 4. Choose all program features will be installed. If you want to change this, Click "Custom", Choose which program features you want installed. Click "Next" to continue. C:\. . . \Wireless LAN Series\ZPlus-B290 C:\Program Files\Wireless LAN Series\WN591 Mini USB Adapter 5. The installer will create a program folder called WN591 Mini USB Adapter . If you want to change this, enter a name or select from the list below. Click "Next" to continue. WN591 USB Mini Adapter 8 6. Start Setup. WN591 Mini USB Adapter WN591 USB Mini Adapter Setup is performing the requested operations. 7. Click "OK" to complete the installation and restart the computer. WN591 Mini USB Adapter The InstallShield Wizard has successfully installed WN591 Mini USB Adapter. Before you can use the program, you must restart your computer. 8. After the computer restarts, plug WLAN USB Adapter connector into USB port on computer. 9 Under MS XP9. After the computer restarts, plug WLAN USB Adapter connector into USB port on computer then Windows XP detects the device automatically, briefly showing a message "Found New Hardware" and starts collecting information for a device information database. USB2. 0-WLAN 10. When Windows XP is ready to cofigure the new hardware, it opens the Found New Hardware Wizard dialog box as shown; a dialog box appears asking what you want the wizard to do. Select "Install the software automatically (Recommended)" and Click "Next". WN591 Mini USB Adapter 10 11. [. . . ] You can select the "Operation Mode" to be Infrastructure or Ad-Hoc. Then you can select the Preamble Type, Power Save Mode, Fragmentation Threshold and RTS/CTS Threshold. Finally, press the "Apply" button. 23 4. 6 Security You can choose WEP function enable or disable. If you decide to use WEP function, you can choose the Authentication Mode, WEP Key Length and Default WEP Key. [. . . ]