User manual COMET LABS ND23000

[. . . ] ND-23000 User Manual ND-23000 Series User Manual (Version: 4. 2) ©Copyright 2005. June 24, 2005 2 Note: Unless otherwise specified, "NAS" refers to Comet Labs ND-23000 models in this document. CUSTOMER SERVICE For the contact details of customer service and technical support, please refer to the registration card. LIMITED WARRANTY In no event shall the liability of COMET LABS Systems, Inc. [. . . ] You may set the share access parameters of each user or user group accordingly. 53 · Quota To allocate disk volume efficiently, you can specify the quota that can be used by each user. When quota is set, users are not allowed to further use disk space once they have reached their quota limit. You can modify the following two options: ü Enable quota for all users ü Quota size on each disk volume 54 3. 8 Network Share Management The primary purpose of network st orage is file sharing. In a standard operation environment, you can create different network share folders for various types of files, or provide different file access rights to users or user groups. By factory default, a "public" share folder is created, which allows full access from all users or guests. There are four options in Network Share Management: i. Remove a network share 55 · Create To create a network share, enter the following information: ü Network share name The share name must not exceed 12 characters and cannot contain the following characters: ". +=/\:|*?<>;[]% ü ü Disk volume This area shows the disk volume status. Path All data are stored under the assigned path onto the disk volume. You can select "Specify path automatically" to allow the server to automatically create a new path on the disk volume to store the network share files. The path cannot exceed 256 characters and cannot contain the characters below: ü Comment Enter a brief description for the share folder. The comment cannot exceed 128 characters. 56 · Access Control Once the network share is created, you can assign access rights to users or user groups: ü ü Deny access Access to the network share will be denied when this option is selected. Read only Users can read the files only on the network share when read only is assigned. ü Full access Users with full access are allowed to read, write, create, or delete files and folders on the network share. 57 · Property and Delete To edit the property of an existing network share, select a share and click Property. You can then edit the content of that share. You can also select to delete an existing network share. Click OK to confirm the deletion or Cancel to abort. 58 3. 9 System Tools System Tools enable you to optimize the maintenance and management of NAS. 3. 9. 1 SNMP Settings Enable SNMP (Simple Network Management Protocol) service and complete all necessary settings to manage network components of the server by SNMP. When enabling SNMP Trap Notification, a message will be sent to a specified trap host when an error occurs. 59 3. 9. 2 Alert Notification Enter the e-mail address of administrator and SMTP server IP address. In case of warning or malfunction, an email will be sent to the administrator automatically. 3. 9. 3 Restart/ Shutdown Select to restart or shut down NAS. 60 3. 9. 4 Hardware Settings You can enable or disable the hardware functions of NAS. Enable LCD panel setting function To enable users to configure TCP/IP settings via the LCD panel. Enable configuration reset switch By enabling this option, you can press the reset button for a few seconds to reset the administrator password and system settings to default. Enable hard disk standby mode Set the minutes when there is no access to the server and the hard disk will go to standby mode. Enable buzzer When buzzer is enabled, an alert sound will be played in case of system err or. Stop network services when a hard disk of RAID fails When a hard disk of RAID configuration fails, network services of NAS will stop. 61 3. 9. 5 UPS If your UPS device provides USB interface, you can enable UPS (uninterruptible power supply) support to protect your system from abnormal system shutdown caused by power outage. In case of utility power failure, the system will shut down automatically by probing the power status of the connected UPS unit. ü Enable UPS support To activate the UPS support, you can select this option. [. . . ] You can inquire AD domain via this DNS server. 128 2. Go to Microsoft Networking of Network Settings. Enable AD Dom ain Member, and enter the domain name and the user name with administrator access right to that domain. Note: (1) Make sure that a fully qualified domain name such as qatest. com. tw has been filled in. (2) Make sure the user name with administrator access right to that domain. 129 3. When the following message appears after applying the settings in step 2, check the DNS IP. When the following message appears after applying the settings in step 2, domain name, domain user name, and the password. When the following message appears after applying the settings in step 2, check the time zone settings. Make sure the difference of your time and that of AD server is less than 5 minutes. [. . . ]