User manual COMET LABS GSM448R

[. . . ] 52-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch with 48×10/100BASE-TX ports 2×1000BASE-T ports 2 mini-GBIC slots (SFP) User's Guide FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. CE Mark Warning This is a Class A product. [. . . ] Plug in the female connector of the provided power cord into this connector, and the male into a power outlet. Supported input voltages range from 100-240V AC at 50-60Hz. 14 UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. Figure 5. LED indicators of the Switch Power and System LEDs POWER: Power Indicator On Off : When the Power LED lights on, the Switch is receiving power. SYSTEM: Management Indicator Blinking On/Off : When the CPU is working, the System LED is blinking. : The CPU is not working. 15 Ports 1~48 10/100M Status LEDs Link/ACT: Link/Activity On Blinking Off : When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. : No link. Ports 49~50 Gigabit Status LEDs Link/ACT: Link/Activity On Blinking Off : When the Link/ACT LEDA lights on, the respective port is successfully connected to an Ethernet network. : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. 10/100/1000 Mbps : On (Green) On (Amber) Off : When the green light is on, the respective port is connected to a 1000Mbps Gigabit Ethernet network. When the Amber light is on, the respective port is connected to a 100Mbps Fast Ethernet network. : When the respective port is connected to a 10Mbps Ethernet or No link 16 Ports 51~ 52 mini-GBIC Status LEDs Link/ACT: Link/Activity On Blinking Off : When the mini-GBIC module is installed and connected to a network, the Link/ACT LED lights on. : When the LED is blinking, the mini-GBIC module is receiving data on a network. : No link. 17 CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN, Trunking, QoS. . . With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware. Installing the Web Management Utility The following gives instructions guiding you through the installations of the Web Management utility. In the Run dialog box, type D:\Web Management Utility\setup. exe (D:\ depends where your CD-Rom drive is located) and click OK. Web Management Utility The Web Management Utility was divided into four parts, Discovery List, Monitor List, Device Setting and Toolbar function, for details instruction, follow the below section. Discovery List This is the list where you can discover all the Web management devices in the entire network. By pressing the "Discovery" button, you can list all the Web Management devices in the discovery list. Double click or press the "Add to monitor list" button to select a device from the Discovery List to the Monitor List. 19 System word definitions in the Discovery List: l l l l l l l l l MAC Address: Shows the device MAC Address. Gateway: Shows the Gateway set of the device. Monitor List All the Web Smart Device in the Monitor List can be monitored; you can also receive the trap and show the status of the device. System word definitions in the Monitor List: l l l l l l S: Shows the system symbol of the Web-Smart device, represent for device system is not alive. System Name: Shows the appointed device system name. 20 l Location: Shows where the device is located. View Trap: The Trap function can receive the events that happen from the Web Management Switch in the Monitor List. [. . . ] Trunk Settings Be sure that the selected trunk setting port must connect to the device with a same VLAN group. Device Status Click on the "Status" to present the device status on this screen, it will show the System Status, Port Status, VLAN Status and Trunk Status . Press "Refresh" when you need to renew the posted information. 33 Statistic The Statistic Menu screen will show the status of each port packet count. Figure 23. Statistics For Detail packet information, click on the ID parameter as Figure 24. 34 Figure 24. 35 System Setting The System Setting includes the System name, Location name, Login Timeout, IP Address, Subnet Mask and Gateway. [. . . ]