User manual COMET LABS GSM2400R

[. . . ] 24-Port 1000BASE-T Web Smart Gigabit Ethernet Switch User's Guide FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. CE Mark Warning This is a Class A product. [. . . ] : When the Power turns off or the power cord has improper connection. SYSTEM: Management Indicator Blinking On/Off : When the CPU is working, the System LED is blinking. : The CPU is not working. 15 Ports 1~24 Status LEDs Link/ACT: Link/Activity On : When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. : When the Link/ACT LED is blinking, the port is transmitting or receiving data on the Ethernet network. : No link. Blinking Off 1000Mbps On : When the 1000Mbps LED lights on, the respective port is connected to a 1000Mbps Gigabit Ethernet network. When the respective port is connected to a 10Mbps Ethernet or 100Mbps Fast Ethernet network Off : 100Mbps On : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. When the respective port is connected to a 10Mbps Ethernet or 1000Mbps Gigabit Ethernet network. Off : 16 CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN, Trunking, QoS. . . With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware. Installing the Web Management Utility The following gives instructions guiding you through the installations of the Web Management utility. In the Run dialog box, type D:\Web Management Utility\setup. exe (D: \ depends where your CD-Rom drive is located) and click OK. Upon completion, go to Program Files -> web management utility and execute the Web Management utility. Web Management Utility The Web Management Utility was divided into four parts, Discovery List, Monitor List, Device Setting and Toolbar function, for details instruction, follow the below section. Discovery List This is the list where you can discover all the Web management devices in the entire network. By pressing the "Discovery" button, you can list all the Web Management devices in the discovery list. Double click or press the "Add to monitor list" button to select a device from the Discovery List to the Monitor List. 18 System word definitions in the Discovery List: l l l l l l l l l MAC Address: Shows the device MAC Address. Gateway: Shows the Gateway set of the device. Monitor List All the Web Smart Device in the Monitor List can be monitored; you can also receive the trap and show the status of the device. System word definitions in the Monitor List: l l l l l l l l l l S: Shows the system symbol of the Web-Smart device, represent for device system is not alive. 19 View Trap: The Trap function can receive the events that happen from the Web Management Switch in the Monitor List. There is a light indicator behind the "View Trap" button, when the light indicates in green, it means that there is no trap transmitted, and else when it indicates in red, it means that there is new trap transmitted, this is to remind us to view the trap. When the "View Trap" button is clicked, a Trap Information window will pop out, it will show the trap information including the Symbol, Time, Device IP and the Event occurred. (Figure 8) The symbol " " represents the trap signal arise, this symbol will disappear after you review and click on the event record. Figure 8. Note: In order to receive Trap information, switch has to be configured with Trap IP and Trap Events in Web browser, which are available in the Trap Setting Menu (see Page 45 for detail). Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you want to monitor. 20 Device Setting You can set the device by using the function key in the Device Setting Dialog box. Configuration Setting: In this Configuration Setting, you can set the IP Address, Subnet Mask, Gateway, Set Trap to (Trap IP Address), System name and Location. Select the device in the Discovery list or Monitor List and press this button, then the Configuration Setting window will pop out as Figure 9, after filling up the data that you want to change, you must fill up the password and press the "Set" to process the data changed immediately. Figure 9. Configuration Setting 21 Password Change: You can use this Password Change when you need to change the password, fill in the password needed in the dialog box and press "Set" button to proceed the password change immediately. Figure 10. [. . . ] The selection of the sniffer mode is as follow: RX (receive) mode: this mode will duplicate the data that send to the source and forward to the sniffer port. Figure 22. Device Status Click on the "Status" to present the device status on this screen, it will show the System Status, Port Status, VLAN Status, Trunk Status and Mirror Status. . Press "Refresh" when you need to renew the posted information. 31 Statistic The Statistic Menu screen will show the status of each port packet count. Figure 23. [. . . ]