User manual COMET LABS CAR-R300

[. . . ] Internet IR Camera User's Manual Internet IR Camera User's Manual Software Version 2. 0. 3 1/78 Internet IR Camera User's Manual Internet IR Camera / Video Server Series Owner's Record The model and serial numbers are located at the bottom. Refer to these numbers whenever you call upon your dealer regarding this product. ____________________ To prevent fire or shock hazard, do not expose the unit to rain or moisture when rear cover be removed. For customers in the U. S. A. This equipment has been tested and found to comply with the limits for a digital device, pursuant to Part 15 of the FCC Rules. [. . . ] A number of up to 10 digits between 0000000000 to 4294967295 is added to the file name. Mode: Send a captured image via three different situations ­ via event such as motion detected or sensor activated or send it periodically. Select "SAVE" to save the setting. 36/78 Internet IR Camera User's Manual SMTP: Setup Mail configuration When alarm was enabled, user can setup the mail to send the captured images to the preset mail address. You may setup SMTP mail parameters for future event-message receiving such as motion detected or sensor activated. SMTP server name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server. Sender's e-mail address: Type the sender's E-mail address. 37/78 Internet IR Camera User's Manual Receiver's e-mail address: Type the receiver's e-mail address. Note: you can key in multiple receiver's email address at the time. Mode: Send a captured image via three different situations ­ via event such as motion detected or sensor activated or send it periodically. Select "SAVE" to save the setting. 38/78 Internet IR Camera User's Manual Motion Detection: Setup motion detection area and sensor sensitivity The motion detection is implemented by a patented software algorithm, it runs on the Internet Camera, due to a larger processing power of motion detection, the overall performance of Internet Camera will be degraded; the frame rate may be reduced. You can enable or disable motion detection. If your enable motion detection, you can also setup detection sensitivity from one of three sensitivity levels. By dragging mouse position on the image, you can see a red-box area which is the motion detection area according to your sensitivity. 39/78 Internet IR Camera User's Manual Time Setting: Setup the Internet Camera time configuration You can setup the Internet Camera time or make it synchronized with PC or remote server. Also, you may select your time zone in order to synchronize time locally. Synchronize the time with PC's time: This is the default time adjust mode, the check box of "Synchronize with PC's time" would be checked by default. Press "SAVE" button to do the time synchronization with PC time. After the "SAVE" button was set, the Internet Camera time will be synchronized as PC's time. From the setting, the Server's time is the same as PC's time. Change the time manually: The following steps can change the time manually 1. Change the time according to the "hh:mm:ss" by 24 hours format. The time was changed by checking the "Server: " time field. 40/78 Internet IR Camera User's Manual Get Time from a NTP server: Select "NTP" Button Key in the NTP server's IP address. After the Internet Camera gets the time from NTP server, it will update the Internet Camera's time field. 41/78 Internet IR Camera User's Manual Popup: Setup event message while motion or sensors has been activated When any one of alarms enabled, and one of them detected, then a message window will be displayed on the screen. You can have output message in case of events activated such as sensors or motion detection to warn user. 42/78 Internet IR Camera User's Manual Firmware upgrade: The Internet Camera supports firmware upgrades (the software that controls the operation in the Internet Camera). COMET LABS will supply the latest firmware version on the COMET LABS Web site at: www. cometlabs. com Download the latest firmware file from COMET LABS's website. Close all other application programs which are not necessary for firmware update. (It must be make sure that the Firmware only apply to 43/78 Internet IR Camera User's Manual Internet Camera, once update, it will be burned into FLASH ROM of system. ) 9. Once the firmware file was selected, select "Upload". 10. [. . . ] Even though the upload speed is more than 128kbps, for optimal video performance, disabling audio streaming will get better video performance. 71/78 Internet IR Camera User's Manual Appendix D: Time Zone Table GMT stands for Greenwich Mean Time, which is the global time that all time zones are measured from. 72/78 Internet IR Camera User's Manual 73/78 Internet IR Camera User's Manual Appendix E: DDNS Application 1. Preface If you have a Cable modem, xDSL, ISDN or Dialup, this is a great way to host your own Web Server, FTP Server, Mail Server, Internet Camera or other TCP/IP Service. (Note: This domain must be registered with Internic via registration authorities such as Network Solutions, DirectNIC, Register. com etc). Your domain name's dynamic IP address is automatically tracked by a DDNS server. [. . . ]