User manual COLEMAN 9943-780
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual COLEMAN 9943-780. We hope that this COLEMAN 9943-780 user guide will be useful to you.
Manual abstract: user guide COLEMAN 9943-780
Detailed instructions for use are in the User's Guide.
[. . . ] Lay all three castings on a level surface with the top (smooth) surface downward.
NH
NH
2-C 2-B
NH MG BV BV
2-D
Another View of Clip (NH)
Right Console Casting
2-A
Left Console Casting
Hardware shown actual size
MG
MG
(NH) Clip (2) Qty.
Alignment Pin BV Alignment Hole
Center Console Casting Right Console Casting 2-A. Lay all three castings on a level surface with the smooth (top) surface downward. Hardware shown actual size
BV
MG
(MG) 1/4-20 x 7/8 Hex Head Cap Screw (8) Qty.
(BV) 1/4-20 Hex Nut (8) Qty.
2-B. Fasten with four SCREWS (MG) and four HEX NUTS (BV) and one Clip (NH). [. . . ] Level and tighten the casters.
11-A
Non-Locking Caster Locking Caster
11-B
Hex Collar
Base
Front
11-A. Use an 11/16" open end wrench to tighten the Hex Collar against the Base Casting.
(Pg. 14)
Step 12
NOTE: Use a ground cloth to protect the paint finish during this step. Check that all fasteners are tightened before turning the grill Right-Side-Up. Carefully turn the grill Right-Side-Up.
12-A
Protect with groundcloth
Control Panel this side.
Protect with groundcloth
Complete Assembly of the Console to the Pedestal.
Step 13
EY
13-A
View of Inside of Main Burner
13-A. Assemble four HEX NUTS (EY) onto the four studs that protrude through the center burner casting. Tighten all fasteners.
Hardware shown actual size
(EY) #10-24 Hex Nut (4) Qty.
(Pg. Fasten BURNER in place per detail 14-D.
Hardware shown actual size
14-A
Right Console
(JD) #10-24 Stamped Wing Nut (2) Qty.
14-D
Burner
Valve Tube
Burner Tube
14-B
Caution: Assemble the wires BELOW the burner tubes!
14-C
JD JD 11-D. Tighten all fasteners.
Step 15
Assemble the BURNER to the LEFT CONSOLE. Move the Flexible Fuel Hose downward to give clearance for inserting the burner tube. The Flexible Fuel Hose and Wiring must be routed BELOW the burner tube per detail 15-D. Left Console
Hardware shown actual size
15-A
(JD) #10-24 Stamped Wing Nut (2) Qty.
15-D
Valve Tube
Flexible Fuel Hose Left Burner
15-B TEST THE IGNITER:
A SPARK SHOULD APPEAR AT
Flexible Fuel Hose
ELECTRODE TIP.
Burner Tube
IF THE SPARK DOES NOT
APPEAR:
-CHECK THE WIRE
CONNECTIONS TO THE
15-C
MODULE.
-CHECK PROPER
ASSEMBLY OF FRESH
9-VOLT BATTERY.
JD JD
Caution: Assemble the wires BELOW the burner tubes!
15-D. 18)
Assemble the DOOR LATCH to the PEDESTAL.
Step 16
16-A
KE
Door Latch KE
16-A. NOTE: You may have to adjust door latch to insure proper alignment of door latch post. Hardware shown actual size
(KE) #6-32 x 3/8 Self-tapping Screw (2) Qty.
Assemble the DOOR HANDLE to the DOOR. Assemble the DOOR LATCH POST to the DOOR.
Step 17
17-A
Door Handle
17-B
Door Latch Post
LF
KE KE
LF
17-A. Attach the DOOR LATCH POST to the DOOR with two SCREWS (CW).
Hardware shown actual size
Hardware shown actual size
(LF) #8-32 x 1/2 Self-tapping Screw (2) Qty.
(KE) #6-32 x 3/8 Self-tapping Screw (2) Qty.
(Pg. Adjust the DOOR LATCH on the PEDESTAL for proper door closure.
Step 18
18-A
Door
GA (4) Places
Door Latch
18-A. Attach the DOOR to the PEDESTAL with four SCREWS (GA).
Hardware shown actual size
18-B. Tighten all fasteners.
(GA) #10-24 x 3/8 Flat Head Screw (4) Qty.
Assemble the MAIN BURNER LID. Adjust the DOOR LATCH on the PEDESTAL for proper door closure.
Step 19
19-A
19-B
IC HB HB IC IC
HB
19-A. Hardware shown actual size
(HB) 3/16 Dia x 1-3/16 LG Clevis Pin (2) Qty.
(IC) Hair Pin (2) Qty.
(Pg. [. . . ] This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province. You can find the nearest authorized Coleman service center by calling 1-800-356-3612. If a service center is not conveniently located, you may call the same number for instructions on shipping the product to the Coleman Company, Inc. You may also call the same number if you have any questions concerning this warranty. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE COLEMAN 9943-780
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual COLEMAN 9943-780 will begin.