User manual COEF MP 300 SPOT

[. . . ] Also in case of sale, rent, change of place and/or ownership, these documents shall be enclosed with the relative equipment. ADVICES FOR A CORRECT INSTALLATION This equipment is destined to an exclusively Professional use. 1) 2) 3) 4) 5) Make sure that all the fastening parts of the spotlight are in good condition. Regulate the proportions of the fastening accessories (screws, bushes, nuts, supports, etc. ) in order to be slightly over-dimensioned as compared to the actual requirements. Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed hereunder is missing, please contact your Dealer immediately. [. . . ] When applying for the repair, always mention the serial number and the model of the equipment. PACKING CONTENTS Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed hereunder is missing, please contact your Dealer immediately: · · · · · Complete MP300 Spot unit This user manual 1 cable with 1 XLR 3 pin male and 1 XLR 3 pin female 1 safety-chain equipped with two snaps. CAREFULLY KEEP THE BOX AND THE COMPONENTS OF THE PACKAGING FOR ANY DISPLACEMENT OR RE-SHIPMENT OF THE EQUIPMENT. Do not leave the packaging elements (polystyrene, nylon, metal parts, etc. ) unattended; they might be dangerous for children. Pag. 4 1. 0 DIMENSIONS & POSITIONING It is possible to set up the MP300 Spot in any position. 540 mm 380 mm 450mm 2. 0 TECHNICAL NOTES MP300 Spot Code: ZL-013101-01 · · · · · · · · · · · · · · · · · · · Lamp: MSD 250/2 ­250 W ­ 2000 H life ­ 8000 K 16 bit movement resolution -PAN 540° / TILT 270°with automatic repositioning Optical system with 3 lenses + dichroic reflector 10 colors + white + bi-colors (with Black light filter) 7 rotating dicroich / metal gobos all interchangeable and indexable on 540° Adjustable strobe Shutter motorized Linear Dimmer from 0 to 100% Rainbow effect adjustable in speed Focus motorized Rotating 3 faces prism adjustable in speed for both directions Multifunction display Remote reset via DMX Remote On/Off lamp via DMX Software upgrade via DMX (with UNI-PROG 8 Accessory) Automatic fault survey Internal power factor correction DMX 512 standard Weight:22Kg Power supply | Absorbed power Volts 230V~ Hz 50Hz I 1. 7A W 380W Pag. 5 3. 0 INSTALLATION The constructor is not be considered responsible in case of: · · · · · · · · · Improper use of the unit or use by not trained staff Use in contrast with the directions on work safety Wrong installation Defective power supply Serious lacks in the necessary maintenance Unauthorized modifications and interventions Use of spare parts that are not original or not specific for the unit Total or partial inobservance of instructions Unusual events 3. 1 LAMP MOUNTING OR REPLACING WARNING: read carefully · · · · · · · · Switch off the projector before operating. The lamp used in the fixture is a high pressure lamp and must be handled very carefully. The unit is realized to use only MSD 250/2 or compatible lamps; absolutely don't use other types of lamp. Wait at least 15 minutes after the projector has been switched off before operating again, in order to let it cool down and avoid the lamp explosion. Don't look directly the lamp. Wait 30 minutes in order to avoid burns. · Unscrew with a cross screwdriver the first screw A for a single turn; unscrew the second one completely B; unscrew completely the screw A and to remove the cover that supports the lampholder. · Insert delicately the lamp in the projector support, driving it with the round cover. Pay attention: the lampholder's wires must correctly reenter in the projector. 6 3. 2 PROJECTOR INSTALLATION To fix the MP 300 Spot is necessary, when the installation has to be on a raised-from-the ground support, to block the quick lock / release brackets of the unit by means of a screw provided with nut and locknut measuring not less than M10 X 50, to insert in the central pre-arranged hole on the fixing bracket. 8 5. 0 SPECIAL FUNCTIONS AND PROJECTOR ASSIGNMENT On the front panel of MP 300 Spot you'll find a section for the additional functions and for setting the projector. Following the picture, you can see all the offered possibilities in detail. All operations are to be carried out with the E, F, G, H buttons, respectively indicated as MENU, ENTER, DOWN and UP. The 3 A, B and C leds will allow you to know: A = reception of the DMX line. C = errors indicated on the ERR table (see table 6. 0). On switching the projector on, the display will indicate the type of projector and the version of control software which have been installed. To this purpose, please remember that this type of projector belongs to a new generation of projectors, designed with the possibility of updating the software version through the normal DMX connection by means of a programmer deliberately created: UNI-PROG 8. After the indication MSTR HOME, the projector carries out the RESET and gets ready to be controlled from the connected console. This means that the first channel occupied by the projector will respond to the values sent to channel 1 by the DMX line. This enables us to make MP 300 Spot (which we are installing) completely independent from control or integral with any other installed projector. General Rules: Refer to the Table of Section 6. 0 in the following page. By each pressure, Button MENU (E) permits to go backwards by one level. [. . . ] 14 9. 2 ELECTRONIC MAINTENANCE WARNING: switch off the projector before operating. This section is dedicated in detail to the electronic connections between the card and the mechanical components, assembled in the projector. These information will be absolutely necessary when the mechanical unit has to be removed from the projector for maintenance and / or repair. The connections are made using handy connectors and are detailed in figure where you can find indications about the connection between a specific connector and a specific component of the mechanical unit. This includes the motors and the sensors of the various effects wheels ( color, gobos, prisms, shutter etc. ). WARNING!An improper use of this documentation made by not specifically qualified staff can damage irremediably the electronic and/or mechanical components of the projector. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Motor SHUTTER / STROBE Motor COLOR Motor GOBOS Motor ROTATION GOBOS Motor PRISM Motor GOBOS FIX Motor FOCUS Motor PRISM ROTATION No connect No connect Motor TILT Motor PAN Encoder TILT Encoder PAN 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Sensor PAN Sensor TILT Sensor PRISM Sensor GOBOS FIX Sensor COLOR / GOBOS / GOBOS ROT. [. . . ]