User manual COBRA XRS 9445 QUICK START GUIDE

[. . . ] Introduction Intro Important Information and Customer Assistance Operation Customer Warranty Assistance Important Information Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio Secondary Icons transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Operating Instructions Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. [. . . ] Customer Warranty Assistance You can reset the activation point at any time to fit your individual preferences and driving style. Customer Setting the IntelliMute Activation Point Assistance Your detector must be installed in your vehicle. Warranty At the desired rev level, press and release the IntelliMute button. Secondary Icons Assistance Three beeps IntelliMute Set All three bars flash three times Installation Secondary Icons Secondary Icons Customer Installation Assistance Customer Assistance 1 2 Notice 3 Caution Notice WarningCaution Warning Installation Notice Notice Caution CAUTION Do not attempt to set the rev point while driving. Warning Your vehicle should be parked and idling. NOTE If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn Off. Tone Four beeps Voice Visual Display IntelliMute must be turned On before setting the activation point. Depending on whether the unit is in Tone Alert or Voice Alert mode, you will hear a series of beeps or voice messages as you follow the steps on the next page. IntelliMute Error, E appears followed by IntelliMute Off X K Ka V S E 10 English Nothing Comes Close to a Cobra® 11 Your Detector Intro Operation Settings Customer Warranty Your Detector Intro Operation Settings Customer Assistance Warranty Assistance IntelliMute Pro IntelliMute Pro prevents detection by radar detector detectors (RDDs) such as VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended for use by experienced users only. OperationSecondary Icons Customer Assistance Voice/Tone Setting You can set your detector to sound alerts with either a Voice or a Tone. In Voice Alert mode, you will first hear several tones, then a voice message announcing the type of signal detected, followed Secondary Icons by more tones. The factory setting is Voice Alert mode. To Change From Voice Alert to Tone Alert While no signal Notice is being detected, press and hold the Mute button for two seconds. Tone One beep Voice Tone Alert Visual Display None When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute activation point, your detector's radar detection circuits are turned Off to prevent detection by RDDs. Customer Before IntelliMute Pro can be turned On, you must have turned On and Set the Assistance IntelliMute activation point. (See pages 9 through 11. ) Notice Warranty Installation Notice Caution CAUTION When IntelliMute Pro is On, NO radar signals will be detected and NO alerts will be given at RPMs below the IntelliMute activation point. Warning IntelliMute Button City Button Press and hold both buttons simultaneously IntelliMute Pro On To Change From Tone Alert Back to Voice Alert While no signal is being detected, press and hold the Mute button for two seconds again. Tone None Voice Voice Alert Visual Display None X K Ka V S c VG-2 and Spectre I & IV+ Alert Settings Police use radar detector detectors (RDDs) to spot users of radar detectors. Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+ RDDs and can provide alerts when any of these or similar devices are in use near your vehicle. Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+ alerts is Off. To Turn VG-2 and Spectre I & IV+ Alerts On and Off To Turn IntelliMute Pro On While no signal Tone is being detected, Two beeps press and hold both the IntelliMute and City buttons for four seconds. To Turn IntelliMute Pro Off Press and hold both Tone the IntelliMute and One beep City buttons for four seconds. Voice IntelliMute Pro Off Visual Display c or h will show steady Voice IntelliMute Pro On Visual Display c or h will blink While no signal is being detected, press and hold the Dim button for four seconds. Tone On = Two Beeps Off = One Beep Voice Spectre VG-2 On Spectre VG-2 Off Visual Display V will blink twice in the display V will blink once in the display 13 12 English Nothing Comes Close to a Cobra® Your Detector Intro Operation Settings Customer Warranty Your Detector Intro Operation Settings and Detection Customer Warranty Assistance Radar Alert Settings Assistance Pop Alert (continued) The detector allows you to choose whether it will show alerts on the X, K and Ku bands. The factory settings are: X Band and K Band On; Ku Band Off. Secondary Icons To Turn Pop Alert On and Off Secondary Icons To Turn X Band On and Off While no signal is Tone being detected, press X On = Two beeps and hold both the Dim and Mute buttons for four X Off = One beep seconds. Notice To Turn K Band On and Off Voice Visual Display X will blink twice in the display X will blink once in the display X On X Off While no signal is being detected, press and hold both the Dim and City buttons for four seconds. Notice Tone Pop On = Two beeps Pop Off = One beep Voice Visual Display P will blink twice in the display P will blink once in the display Pop On Pop Off While no signal is being detected, press and hold both the Mute and City buttons for four seconds. Tone K On = Two beeps K Off = One beep Voice Visual Display K will blink twice in the display K will blink once in the display K On K Off Detection Signals Detected · The tables on the following pages show you the types of Signals your detector will detect, as well as the voice and visual alerts it provides for each of them. To Turn Ku Band* On and Off While no signal is being detected, press and hold the City button for four seconds. Tone Ku On = Two beeps Ku Off = One beep Voice Ku On Ku Off Visual Display X and K will blink twice in the display X and K will blink once in the display Audio Alerts In Voice Alert mode you will first hear several tones, then a voice message announcing the type of signal detected, followed by more tones. In both Voice Alert and Tone Alert modes, a distinctly different alert tone is used for each type of signal detected (including separate tones for each laser signal). For X, K, Ka and Ku band radar signals, the tones will repeat faster as you approach the signal source. [. . . ] Additional patents may be listed inside the product or pending. Your detector is designed and built to give you years of trouble-free performance without the need for service. If your unit does not appear to be operating properly, please follow these troubleshooting steps: s Make sure the power cord is properly connected. s Make sure the socket of your vehicle's cigarette lighter is clean and free of corrosion. s Make sure the power cord's cigarette lighter adapter is firmly seated in your cigarette lighter. [. . . ]