User manual COBRA MT 975

[. . . ] 10376 MT975_ENG. qxd 1/15/08 3:57 PM Page 1 Two-Way Radio Model MT 975 ENGLISH 1. Lock Tab 12 9 4 1 2 11 10 3 8 5 6 13 7 14 Product Features · Two-Way Radio with up to a 12 km (7. 5 mile) range · 8 Channels* · 38 CTCSS Privacy Codes · 83 DCS Privacy Codes · 10 Channel Memory · Backlit LCD Display · Battery Saver Circuitry · Battery Level Meter · Maximum Range Extender · VOX Mode for Hands-Free Transmissions · Intercom Capable · Baby Monitor Function · VibrAlert® Silent Paging · Call Alert 10 Selectable Tones · Scan Channels, Privacy Codes, Memory · Dual Watch Programmable 2-Location Scan · Key Lock · Auto Squelch · Selectable ON/OFF "Roger Beep" Confirmation Tone · Selectable ON/OFF Keystroke Tone · Combination Speaker/Microphone Jack · Belt Clip *You are not allowed to use channels 1 and 2 in France. This situation can change; please contact the French radio licensing authority for more information. 480-439-P Version A 10376 MT975_ENG. qxd 1/15/08 3:57 PM Page 2 OPERATION English Use only the supplied rechargeable batteries and rapid desktop charger for recharging your microTALK® radio. [. . . ] Press the TALK button to return to LISTENING MODE on the selected memory location. NOTE: A memory location can be reprogrammed at any time it is displayed and flashing. While recalling a stored memory location, if you do not press any buttons for 15 seconds, your radio will automatically return to LISTENING MODE on the channel/privacy code displayed before you entered MODE functions. Press the MODE button until the Memory icon and the memory location flash on the display. English Channel Scan Your microTALK® radio can automatically scan channels (1 to 8). NOTE: The radio ignores specific CTCSS or DCS privacy codes while scanning channels. Press the MODE button until the Scan icon and the channel number flash on the display. Press the CHANNEL UP or CHANNEL DOWN button to begin scanning channels. Your radio will continue to scan all channels and stop if an incoming transmission is detected. During An Incoming Transmission, You Can Choose From The Following: a. Press the CHANNEL UP or CHANNEL DOWN button to resume scanning channels. If you do not press any button within 10 seconds, your radio will automatically resume scanning channels. 2. Press the CHANNEL UP or CHANNEL DOWN button to select the memory location (0 through 9). NOTE: If a location has been programmed before, its associated channel/privacy code will be shown on the display. Press the CHANNEL UP or Channel O CHANNEL DOWN button to select Channel O. Press the LOCK/ENTER button to enter the channel/privacy code in the selected memory location and return to the beginning of memory location options. Press the MODE button to enter the channel/privacy code in the selected memory location and proceed to other functions on the channel/privacy code displayed before you entered MODE functions. While de-programming a memory location, if you do not press any buttons for 15 seconds, your radio will automatically return to LISTENING MODE on the channel/privacy code displayed before you entered MODE functions. Privacy Code Scan Your microTALK® radio can automatically scan the Privacy Codes (either CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only one set of privacy codes (CTCSS or DCS) can be scanned at a time. While in LISTENING MODE, press the CHANNEL UP or CHANNEL DOWN button to choose the channel on which you wish to scan Select Scan Privacy privacy codes. Press the MODE button until either the CTCSS or the DCS icon appears on the display and the Scan icon and the small numbers next to the channel number flash on the display. Press the CHANNEL UP or CHANNEL DOWN button to begin scanning privacy codes within the channel you selected. The Scan icon will continue to be displayed when privacy code scan is ON. [. . . ] Baby Monitor uses the same sensitivity level you set for the VOX Function. If you have not set a VOX sensitivity level (see the "Voice Activated Transmit [VOX]" section of this manual), the maximum sensitivity, level 5, will automatically be used. Press MODE button until the Select Baby Monitor Baby Monitor icon flashes on the display. Press the CHANNEL UP or CHANNEL DOWN button to change the setting to ON. [. . . ]