User manual COBRA ESD6200ML

[. . . ] ESD-6200. MANUAL. qx 10/23/98 3:48 PM Page 1 Installing and Using Your 1. What You'll Need To Install The ESD-6200: NOTE: Detailed instructions on opposite side 3. Turn On and Adjust Volume LEDs are briefly illuminated at Power ON F. Indicators and Visual Alerts Power VG-2 DETECTION SYSTEM Model ESDTM-6200 Illuminates when On Blinks at a steady rate Lights Up Safety Alert® Warnings B. [. . . ] The ESD-6200 will announce the reception of speed monitoring and Safety Alert signals as follows: "Be Careful. . . " Voice Alert Message: "X Alert "K Alert" "Laser Alert" "VG-2 Alert" "Ka Alert" F. VG-2 Undetectable Some states or municipalities use devices referred to as "VG-2". The VG-2 device detects low level energy radiated by the internal oscillators of radar detectors. The ESD-6200 detects the VG-2's radiation before the VG2 can detect the ESD-6200. The ESD-6200 then briefly turns off its internal oscillator, rendering it invisible to the VG-2, and alerts you to VG-2's presence. During these short intervals, the ESD-6200 is not able to receive radar or Safety Alert signals (laser reception is not affected). Band Alarm Indicators When the Cobra ESD-6200 detects an X-band radar signal, the red "X" Visual Alarm Indicator (LED) will flash in unison with the X-Band audio tone. When the ESD-6200 detects a K-band signal, the amber "K" Visual Alarm Indicator will flash in unison with the K or Ka Band audio tone. When the ESD-6200 detects a Ka-Band radar signal, the (color) "Ka" Visual Alarm Indicator will flash in unison with the Ka-Band Audio Tone. When the ESD-6200 detects pulses of laser light, the yellow "L" LED will flash in unison with the Laser tone. When VG-2 is detected, the amber "VG-2" LED will flash with an audio tone. When a Safety Alert signal is detected, the pattern of signal meter will indicate that a Safety Alert signal is being received and which type it is. Mute/AutoMute Button Manual Mute: The mute function is controlled by a momentary button. The detector will automatically reset to normal operation after the alert has passed. AutoMute: When in AutoMute the unit will reduce the audible sound by half after four seconds of the warning. Switching from AutoMute/Manual Mute: When no signal is present, pressing this button for less than 2 seconds will switch the unit between AutoMute Mode and Manual Mute. A double beep will confirm unit is in AutoMute and a single beep will confirm unit is in Manual Mute Mode. When in the Voice Mode, the ESD-6200 will announce "Auto Mute" or "Mute". Switching from Tone/Voice+Tone: When no signal is present, pressing the button for more than 2 seconds will switch the unit between Tone and Voice+Tone Mode. A "Voice Alert" will confirm Voice+Tone has been selected and a single beep will confirm that Tone Only Mode has been selected. "Be Careful. . . " Safety Alert Warnings: "Emergency Vehicle Approaching" "Road Hazard Ahead" "Train Approaching" The message "Be Careful. . . " and the Voice Alert Message will sound at the start of the alert. The Voice Alert Message will be followed by the corresponding Tone Alerts. Instant-on Detection The Cobra ESD-6200 is also designed to detect Instant-on speed monitoring signals. [. . . ] This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U. S. A. COBRA will, without charge, repair or replace, at its option, defective radar detectors, products or component parts upon delivery to the COBRAfactory Service Department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt. You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Cobra's expense, if the product is repaired or replaced under warranty. For further details concerning procedures for obtaining service, see the "If You Think You Need Service" section of the Owner's Manual. [. . . ]