User manual COBRA CP9135ML

[. . . ] CP9135 manual layout. 6 10/20/98 12:41 PM Page 1 CP-9135 Cobra Electronics Corporation 6500 West Cortland Street Chicago, IL60707 FCC Information FCC Information Included Accessories 1 Registered with The FCC Please note: This cordless phone operates under part 15 and part 68 of FCC rules. Operation is subject to two conditions: 1. It may not interfere with radio communications, and 2. It must accept any interference received, including that which may cause undesirable operation. See the Operational Features section of this manual for ways to reduce interference. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Operating Instructions for your Cobra CP-9135 If You Think You Need Service For technical assistance, please call our Automated Help Desk which can assist you by answering the most frequently asked questions about Cobra products. Private Call® 900 2 (773) 889-3087 24 hours a day, 7 days a week. [. . . ] To raise or lower the volume, push the UP arrow for higher volume;push the DOWN arrow for lower volume. 1 Push and release the button, which shuts off the base microphone. You will still be able to hear your caller but they will not be able to hear you or a conversation you might be having. Mute 2 Hearing Aid Compatibility Hearing Aid Compatibility The CP-9135 handset is compatible with induc tively coupled hearing aids (HAC). Push and release the button again to rejoin the conversation. The Mute will go off on the base. 20 21 CP9135 manual layout. 6 10/20/98 12:41 PM Page 28 Operation Last Number Instant Redial Last Number Instant Redial Each time you dial a number, that number is stored in the REDIAL memor y. To recall the number after receiving a busy signal: handset or base Operation Last Number Delayed Redial If steps 1, 2 and 3 from the "Last Number Instant Redial" still result in a busy signal, hang up. If you would like to try again in a few minutes, push and release TALK button for dial tone, then: handset or base Last Number Delayed Redial 1 2 Push and release FLASH button. The number will be redialed. 3 4 Push and release REDIAL/PAUSE button. 23 22 CP9135 manual layout. 6 10/20/98 12:41 PM Page 30 Operation Memory Number Storage Memory Number Storage The CP-9135 will store up to 10 frequently called numbers. Operation Note To store numbers from the base follow the same proceedure used for the handset. Memory 3 Push and release button again. There will be 2 double beeps. Note 1. You may also use the button in memory to temporarily change from pulse to tone dialing. Note Memory 1 Push and release button once. 4 Assign memory position by en tering keypad number from 0 to 9. Repeat for additional numbers to be stored in memory. Enter name beside MEMORY number on the memory label provided with the unit. 2 Enter digits of number to be stored (up to 16). 24 25 CP9135 manual layout. 6 10/20/98 12:41 PM Page 32 Operation Memory Number Dialing Memory Number Dialing 1 Operation To Find The Handset The handset can be located when it's away from the base. To locate the handset: Access a line. To Find The Handset Note Memory dialing from base uses same procedure as handset. Memory 2 Push and release button once. Page/Find 1 Push and release button. The handset will beep for 30 seconds, allowing time to locate the handset. 3 Pushand release keypad number, (0-9), you assigned for that phone number. The phone will dial that number automatically. 2 If you wish to stop beep tones push and release Talk or buttons, wait 2 seconds, push and release again or, push and release button on base. Intercom Intercom Page/Find 26 27 CP9135 manual layout. 6 10/20/98 12:41 PM Page 34 Operation Intercom Mode From The Handset Intercom Mode From The Handset Your CP-9135 can serve as an intercom between the base and the handset. To utilize this feature: Operation Intercom Mode From The Base Intercom Mode From The Base Note Intercom may be initiated from either the handset or the base. Intercom Page/Find Note To initiate INTERCOM while on Hold a call, push and release button. Then push and release Intercom Page/Find button. Push and Intercom release button to end. 1 1 Push and release will illuminate. Intercom button. The Intercom LED Push and release flash on the base. button. The In Use LED will Low Batt 2 The and LED will light on the base. Begin talking. Intercom In Use 2 The Intercom LED on handset will flash and handset will beep. 3 28 29 CP9135 manual layout. 6 10/20/98 12:41 PM Page 36 Operation Intercom Mode From The Base continued Hold Button On The Handset and Base handset or base Operation Hold Button On The Handset and Base Note When parties are on hold, both Line 1 and/or Line 2 LEDs will b e flashing. The INUSE LED will be illuminated on the base. 3 The person using the handset should push and release the button. Intercom 1 4 Begin talking. 2 Push and release HOLD button to put a par ty on hold to answer other line or to pr event other party from hearing you. To release HOLD push and release the line button that is illuminated on the base or pick up a branch phone on the same line. 30 31 CP9135 manual layout. 6 10/20/98 12:41 PM Page 38 Operation Conference Calling From Handset And Base Conference Calling Using Both Lines Your CP-9135 makes conference calls easy and convenient. 1 Operation handset or base Access a line. When the party is reached: or base 4 handset Note Conference calls can be initiated from both the handset and the base. Dial other party. 4-way conferencing can be accomplished by using the handset and the base. To end a 4-way conference, handset and base must end the call. Note To conference an incoming call while on a call, place current call on Hold and answer other call. Note To drop one party from the conference call, push and release the line button for the party you wish to keep. To end both conversations, push and release the Talk or buttons. Speakerphone 2 Push and release HOLD button. 3 Push and release other line. 33 32 CP9135 manual layout. 6 10/20/98 12:41 PM Page 40 Operation Ringer Switches Ringer Switches RINGER ON/OFF switches are located on the base. [. . . ] First, you are further from the source of interference and secondly the power adapter for the cordless phone will b e plugged into an outlet, which most likely is on a different line than the appliance which is causing the interference. If the noise persists after relocating the base, move closer to the base unit when talking on the phone. If the noise disappears, then it is most lik ely local interference being generated by a source outside your home, or a source inside your home strong enough to blanket your entire house such as a baby monitor. If you find that the noise and interference are equally strong throughout your house, your cordless phone may require service. [. . . ]