User manual CLIFFORD XL 2000

[. . . ] For instance, pressing button II while the alarm is armed will either: TO DISARM THE SYSTEM. . 5 Turn on the headlights for any duration you wish between 1 second and 2. 5 minutes (factory setting is 30 seconds; to change duration, see User-Selectable Features on pages 9-10) OR . 5 Fully close all the power windows and sunroof on various Jaguar, BMW and Volkswagen vehicles. 3 TO ACTIVATE AN OPTION WHEN THE ALARM IS DISARMED . . As previously noted, button II (switch up) can control another option when the system is disarmed. [. . . ] You can also use buttons II and IV to activate other options. Enhanced AutoArmingTM If you forget to remotely arm the system, it will arm itself automatically ("passively") 30 seconds after the vehicle doors are closed. If you re-open any door(s) within the 30-second countdown, AutoArming will restart from the beginning once all doors are closed. This ensures you'll never accidentally leave your vehicle unprotected. XL2000 includes all these Enhanced AutoArming features: AutoArming Enable/Disable: If you prefer, you may deactivate or reactivate AutoArming. Visual Acknowledgment: Five seconds after you exit the vehicle and close all the doors, the parking lights will flash twice to confirm that the AutoArming countdown is progressing. AutoArm & Lock: To ensure you can't accidentally lock your keys inside the car, the system is factory-set not to lock the doors upon AutoArming. NOTE: To prevent AutoArming of the system when fueling the vehicle, either enable valet mode or leave one of the doors open (the system AutoArms 30 seconds after all doors are closed). 5 Smart AutoTestingTM Each time you remotely arm your vehicle, it will perform a series of tests on all triggers and sensors. If a trigger malfunction is found, you will be visually and audibly alerted immediately with 4 chirps and flashes instead of the usual 2. If a sensor is malfunctioning, you will receive the usual 2 chirps and flashes, then, a few seconds later, there will be 4 chirps and flashes. Specific Malfunction Identification: The system not only tells you if the problem is a trigger or sensor, but it can also indicate the specific trigger or sensor that is malfunctioning. (To disable FACT, see User-Selectable Features on pages 9-10. ) Dual-Mode Tampering Warning Normally, the system immediately sounds its six-sound siren at the first inkling of an intrusion attempt. However, you may set the system to issue a rapid five-chirp warning whenever the system detects tampering to the exterior of your vehicle. If there is any further tampering within the next 30 seconds, or if a door, the hood or trunk is opened at any time, your system will sound a continuous 125dB six-sound siren blast. To select the mode of your choice, see User-Selectable Features on pages 9-10. NOTE:Turning on the Tampering Warning feature overrides the FACT feature, and vice-versa. Smart Prior Intrusion Attempt Alert When you remotely disarm, if you hear 3 chirps instead of the usual one chirp it means that a trigger or sensor was activated in your absence. When you enter the vehicle, the LED will blink several times, pause, then repeat the blink cycle 4 more times. Count the number of blinks in one cycle and refer to the chart below: Number of LED blinks per cycle after disarming 1 blink 2 blinks 3 blinks Trigger/Sensor Activated Magnetic Resonance Sensor Door trigger Trunk or hood trigger AutoLock/AutoUnLock For your safety and that of your passengers, the system automatically locks the doors when you turn on the ignition switch to start the engine and unlocks them once the ignition is turned off. See the User-Selectable Features section on pages 9-10. Siren Duration When the system detects an intrusion attempt, the alarm is set to sound for 30 seconds. See the User-Selectable Features section on pages 9-10. 7 AntiScan Car thieves use electronic scanners that rapidly transmit one remote control code after another to defeat ordinary alarms. AntiScan prevents scanners from disarming your system. Automatic Fault-Proof Starter Interrupt The system automatically prevents engine starting while the system is armed but allows you to start it even in the unlikely event of a full system failure (other manufacturer's alarms may leave you stranded). Multi-Level Chirp Control Whenever you wish, you may lower the volume or completely silence the system's arm/disarm chirps. The short-term and one-time chirp muting capabilities are especially valuable when parking late at night in a quiet residential area. You have several choices: Chirp Volume Control: Lets you lower the volume of the chirps or restore them to full volume. [. . . ] Immediately flick the valet switch back and forth, counting the number of chirps you hear. You will hear one or more chirps (as noted in the "program completion confirmation" section) to confirm that you have changed the feature setting. Programming Table for User-Selectable Features Feature # of Factory flicks & setting chirps ON 4 Secondary action Program completion confirmation 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step Result AutoArming AutoArm & Lock Arm/Disarm Chirp Confirmation Chirp Volume Headlights On Reminder AutoLock/ AutoUnLock -- Change state from ON to OFF or vice-versa Change state from ON to OFF or vice-versa Change state from ON to OFF or vice-versa Changes state from LOUD to SOFT volume or vice-versa Change state from ON to OFF or vice-versa Change state from ON to OFF or vice-versa OFF 5 -- ON Full Volume ON 6 -- 7 -- 8 -- ON 9 -- 9 Feature Siren Duration Tampering Warning FACT -- False Alarm Control and Test Add a New Remote to Channel 1 (arm/disarm) Add a New Remote to Channel 2 (optional remote accessory) Add a New Remote to Channel 3 (silent arm/disarm) Add a New Remote to Channel 4 (optional remote accessory) Built-In Timer D # of Factory flicks & setting chirps 30 sec. 10 Secondary action Program completion confirmation Result -- 1 chirp 3 Change duration from 30 seconds after to 60 seconds or vice-versa last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last tap Change state from OFF to ON or vice-versa Change state from OFF to ON or vice-versa OFF 11 -- ON 12 -- -- 13 Press remote control button I (switch UP) 1 chirp Button I/channel 1 code of new remote control has been memorized -- 14 Press remote control button II (switch UP) 2 chirps Button II/channel 2 code of new remote control has been memorized -- 15 Press remote control buttons III (switch UP) 3 chirps Button III/channel 3 code of new remote control has been memorized -- 16 Press remote control button IV (switch UP) 4 chirps Button IV/channel 4 code of new remote control has been memorized 30 sec. 17 3 seconds later, 1 chirp will indicate that the timer has started. [. . . ]