User manual CLIFFORD XL 1000

[. . . ] The lights will flash repeatedly and the siren will blare for 30 seconds or until you press button I again to turn it off. If you have an optional Clifford 4-button/4-channel remote control, press button IV to activate another remote controlled option, such as the Clifford IntelliStartTM remote engine/ heater/defroster/air conditioner starter accessory (refer to the IntelliStart's operating instructions). 1 TO DISARM THE SYSTEM. . AutoLock/AutoUnlock For your safety and that of your passengers, the system automatically locks the doors when you turn on the ignition switch to start the engine and unlocks them once the ignition is turned off. [. . . ] The LED will turn off to indicate that the alarm is in normal operating mode. Keyless Entry in Valet Mode: Even if valet mode is on, you will still be able to remotely control all the convenience features. For instance, simply press button I as if you were arming or disarming and your car's doors will lock or unlock. You can also use button II to activate an option. 2 Tampering Warning Normally, the system immediately sounds its siren at the first inkling of an intrusion attempt. However, you may set the system to issue a rapid five-chirp warning whenever the system detects tampering to the exterior of your vehicle. If there is any further tampering within the next 30 seconds, or if a door, the hood or trunk is opened at any time, your system will sound a continuous 125dB siren blast. To select the mode of your choice, see User-Selectable Features on pages 6-7. NOTE: Turning on the Tampering Warning feature overrides the FACT feature, and vice-versa. FACTTM-- False Alarm Control and Test With FACT, you'll never experience repeated false alarms. If your siren goes off, DO NOT remotely disarm the system; allow it to run for the full 30-second siren duration. The system automatically checks for another activated trigger before sounding the siren a second time. Should the siren sound again, you will know for sure that someone is tampering with your vehicle. Automatic Starter Interrupt The system automatically prevents engine starting while the system is armed. Only after disarming will the system allow the engine to be started with the ignition key. Smart AutoTestingTM Each time you remotely arm your vehicle, it will perform a series of tests on all triggers and sensors. If a trigger malfunction is found, you will be visually and audibly alerted immediately with 4 chirps and flashes instead of the usual 2. If a sensor is malfunctioning, you will receive the usual 2 chirps and flashes, then, a few seconds later, there will be 4 chirps and flashes. Specific Malfunction Identification: The system not only tells you if the problem is a trigger or sensor, but it can also indicate the specific trigger or sensor that is malfunctioning. This feature saves you time and money since your installer won't have to spend hours trying to determine where the problem is. The LED indicator inside the vehicle will be flashing, pause, then repeat. Count the number of blinks in one cycle between pauses (for your convenience, the blink cycle repeats 5 times) and refer to the chart below: Number of LED blinks between pauses 1 blink 2 blinks 3 blinks 3 Malfunction Vibration/impact sensor or optional sensor Door trigger Trunk or hood trigger Automatic Malfunction Bypass To provide the utmost protection even if a system component malfunctions, the system will automatically bypass the faulty point and arm all other triggers and sensors until you can have the system serviced by your local Authorized Dealer. Smart Prior Intrusion Attempt Alert When you remotely disarm, if you hear 3 chirps instead of the usual one chirp it means that a trigger or sensor was activated in your absence. When you enter the vehicle, the LED will blink several times, pause, then repeat the blink cycle 4 more times. Count the number of blinks in one cycle and refer to the chart below: Number of LED blinks per cycle after disarming 1 blink 2 blinks 3 blinks Trigger/Sensor Activated Vibration/impact sensor or optional sensor Door trigger Trunk or hood trigger TotalRecallTM The system's non-volatile memory records the identity of the last activated or malfunctioning trigger or sensor, which allows your installer to instantly track down a malfunction and save you servicing costs. To identify the trigger or sensor held in the system's non-volatile memory, simply perform the following procedure: 1. [. . . ] To remotely arm or disarm the alarm silently, press buttons I+II on the remote control. 5 User-Selectable Features Your XL1000 vehicle security system allows you to set many of its features to your own personal preferences. We have made the programming procedures very simple: to make a change, you just flick the valet switch a few times. The system comes from the factory with all of its features pre-programmed as noted in the table below and on page 7. [. . . ]