User manual CLIFFORD SOLARIS 5

[. . . ] Solaris 5 Owner's Guide limited lifetime consumer warranty Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. [. . . ] This technology has been developed to increase the security of the unit. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. © 2 0 0 3 d i re c t e d e l e c t ro n i c s , i n c . 19 power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery and prevents the system from draining the battery. Power Saver Mode takes over under the following conditions: Power Saver when the system is armed: After the system has been armed for 48 hours, the LED will flash at half its normal rate, decreasing the system's current draw. Power Saver in Valet Mode: When the system enters Valet Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet Mode, the LED will shut off. If the system remains in Valet Mode, the LED will come back on and restart the 1 hour timer the next time the ignition is turned off. 20 programming cliffnet wizard installation software programming Cliffnet Wizard provides access to all available system features and some that are not available when manually programming with the Valet switch. Cliffnet Wizard is compatible with Microsoft Windows 95/98/2000/ME/XP/NT so most programming operations can be accomplished by pointing and clicking with a mouse. This eliminates the need for programming grids and lengthy programming sequences. For a complete guide to system programming using the Cliffnet Wizard refer to the Cliffnet Wizard help menu. manual programming instructions Be sure to document changes by taking note of all feature changes made in programming mode. Ignition on - Turn the ignition to the run position or start the engine. Enter PIN - Enter the factory preset PIN code 2 by pressing on the PlainView 2 Valet switch twice, then once. note: If the factory preset PIN has been changed, the new PIN must be entered. © 2 0 0 3 d i re c t e d e l e c t ro n i c s , i n c . 21 3. Hold/Chirp/Release - After entering the PIN code, press and hold until a chirp is heard and the LED turns on, then release the button. You have now entered the feature selection position of the User Selectable Features grid. After a pause the siren will chirp the same number of times as the selected column for confirmation. Feature select - Press the same number of times as the desired feature. If the system chirps once, the feature has just turned off; if the system chips twice, the feature has just turned on. If the feature has more than two settings, continue pressing on the transmitter to toggle through the settings. You can advance to any feature in the same column by pressing within 60 seconds; to program a feature in a different column begin at step 4 within 60 seconds. note: Refer to the Feature Descriptions sections of this guide for important notes and descriptions of the system features and programming. 4. 5. 6. 7. Exit programming - To exit programming mode turn the ignition off or wait 60 seconds without pressing the PlainView 2 Valet switch. The siren will chirp three times to indicate programming mode has been exited. 22 user selectable features Then Press First Press Add new remote (autolearn) Auto (passive) arm on/off Chirps on/off/quiet Auto lock ignition/off/rpm Auto unlock ignition/off Auto (passive) arm and lock on/off Siren duration 30/60/90 Second unlock on/off Not used Set PIN code (default = 2) Select siren sounds FACT II on/off Remote valet on/off Entry delay on/off Reset to default (except transmitter and valet code) Panic on/off Autostart setting* (off/battery only/ temp only/ battery and temp) Not used New remote learn arm/disarm only New remote learn accessory A channel New remote learn accessory B channel New remote learn silent mode New remote learn remote valet New remote learn remote start* New remote learn window down/vent** Not used Clear all remotes * This feature is only available with optional IntelliStart connected. [. . . ] to decrease sensitivity. The sensor Primary zone can be tested at any time during adjustment by striking the vehicle which will generate 1 siren chirp each time the zone is activated. Adjust Warn-away Zone NOTE: There are 16 distinct pitch settings, if the upper or lower limit of the 16 settings is reached the siren will emit 2 chirps at the default pitch. Press of the remote control to increase sensitivity. The sensor Warn-away zone can be tested at any time during adjustment and will generate 1 siren chirp each time the zone is activated. Press of the remote control to return to Primary zone adjustment and lock in Warn Away zone setting. [. . . ]