User manual CLIFFORD SMART REMOTE START 3

[. . . ] World-Class Auto Security TM Smart Remote Starter Owner's Manual WARNING The Smart Remote Starter III system is designed to be used ONLY on a fuelinjected, gasoline or diesel powered vehicle with an automatic transmission. Installing a Smart Remote Starter III on a vehicle that has a manual transmission poses an EXTREME SAFETY RISK!Never install a Clifford remote engine starting product on a manual transmission vehicle. Always exercise good judgment and common sense when using the remote starter: · NEVER remotely start the vehicle in an enclosed area without suf ficient ventilation. · NEVER engage the ShortStop nor one or both AutoStart features if the vehicle is in an enclosed area without adequate ventilation. [. . . ] The engine will continue to idle under the control of your Smart Remote Starter III for up to 30 minutes. When you have completed your errand, just use the normal procedure noted in the To drive the vehicle section on page 8. 8 Interfacing with factory theft deterrent devices If your vehicle has a factory-installed theft deterrent device, the Smart Remote Starter III can make it a full-fledged remote controlled car alarm, arming the device every time you remotely lock the doors and disarming every time you remotely unlock. AutoLock and AutoUnLock (user-selectable) For your safety and that of your passengers, the doors automatically lock when you begin driving at about 15-20mph, and automatically unlock when you turn the ignition off. To suit your preferences, you may turn off either or both the AutoLock and/or AutoUnLock features. There are four possibilities: AutoLock "on" while AutoUnLock is "off, " or vice-versa. The other two combinations are both AutoLock and AutoUnLock "on" or both "off. " As set from the factory, both features are on. To change the status of one or both features, see the User-selectable features section on page 13. Fault-proof starter Interrupt When you remotely lock the doors, your Smart Remote Starter III engages its starter interrupt circuit that prevents a thief from cranking the engine's starter even if he has a duplicate of your car key. Whenever you see the LED flashing on the system's PlainView switch, the starter interrupt is engaged and protecting your vehicle. AutoActivation of the starter interrupt (user-selectable) Smart Remote Starter III will protect your vehicle even if you forget to remotely lock the doors (and thus activate the starter interrupt). Thirty seconds after you park your car, exit and shut all the doors, the Smart Remote Starter III will automatically ("passively") activate the starter interrupt (if a door is re-opened during the 30-second countdown, the countdown will resume from the start once all doors are closed). To provide visual confirmation, the system will flash the dashboard LED twice 5 seconds after you close the doors to signal the start of the 30-second countdown. To clear the starter interrupt, just press button 1 on your remote control. If you prefer, you may turn off the starter interrupt autoactivation feature (see User-selectable features on page 13). Also see the UltraSecure coded valet mode section on page 10 for information on temporarily overriding autoactivation. AutoActivation of the door locks (user-selectable) If you wish, you may set the system to automatically lock the doors every time it AutoActivates the starter interrupt. To ensure that you can't accidentally lock your key and remote inside the vehicle, this feature is factory set off. To enable this feature, see the User-selectable features section on page 13. 9 UltraSecureTM coded valet mode Your secret valet code In seconds, thieves can disable all non-Clifford starter interrupt systems and alarms by hotwiring the ignition and flicking an easy to find "hidden" valet switch. Your Smart Remote Starter III has safeguards that absolutely ensure that a thief cannot enable the valet mode as a way of "turning off" your system's starter interrupt. To enable valet mode, the driver must first enter a secret valet code on the PlainView switch. the code can be any number between 1 and 999, except those that contain a zero). Whenever the system is put in valet mode, it overrides autoactivation of the starter interrupt (see page 9). [. . . ] Or, for even greater ease, just press remote control button 4 to remotely activate both AutoStart features (two flashes of the parking lights will confirm remote activation of the AutoStart features). Optional remote headlight activation and/or remote trunk release Button 3 on your remote control can command two different options: one while the system's starter interrupt is engaged and another while it is disengaged. If you have the optional remote headlight activation feature installed, a single press of button 3 while the system's starter interrupt is engaged (i. e. , the LED is flashing) will activate the system's built-in timer to illuminate the headlights for any duration of your choice between 1 second and two minutes. To change the headlight duration, see User-selectable features on page 13. [. . . ]