User manual CLIFFORD SABRE

[. . . ] Use it to arm or disarm the system, lock or unlock the doors, activate its panic feature or control options such as headlight activation or remote trunk release. TO ARM THE SYSTEM. The dashboard LED will flash repeatedly and the car doors will automatically lock (some vehicles require an optional power lock adaptor). Any attempt to break into the vehicle will immediately disable the starter, sound the siren and flash the parking lights. In addition, the car doors will automatically unlock (some vehicles require an optional power lock adapand the interior lights will turn on and stay on for 30 seconds or until you start the engine. [. . . ] Be sure to ask your installer to show you where the valet switch is located. To turn ON the protected valet mode: 1. Insert your ignition key and turn it to the "ON" position, or start the engine. The LED will glow continuously to indicate that the alarm is in valet mode. To turn OFF the protected valet mode: 1. Insert your ignition key and turn it to the "ON" position, or start the engine. The LED will turn off to indicate that the alarm is in normal operating mode. Keyless Entry in Valet Mode: Even if valet mode "on", you will still be able to remotely control the convenience features. For instance, simply press button I as if you were arming or disarming and your car's doors will lock or unlock. You can also use button II to activate an option. Optional Automatic Starter Interrupt If equipped with an optional relay, the system automatically prevents engine starting while the system is armed. Only after disarming will the system allow the engine to be started with the ignition key. 2 Tampering Warning Normally, the system immediately sounds its siren at the first inkling of an intrusion attempt. However, you may set the system to issue a rapid five-chirp warning whenever the system detects tampering to the exterior of your vehicle. If there is any further tampering within the next 30 seconds, or if a door, the hood or trunk is opened at any time, your system will sound a continuous 125dB siren blast. To select the mode of your choice, see User-Selectable Features on pages 5-6. NOTE:Turning on the Tampering Warning feature overrides the FACT feature, and vice-versa. FACTTM-- False Alarm Control and Test With FACT, you'll never experience repeated false alarms. If your siren goes off, DO NOT remotely disarm the system; allow it to run for the full 30-second siren duration. The system automatically checks for another activated trigger before sounding the siren a second time. Should the siren sound again, you will know for sure that someone is tampering with your vehicle. LED Status Indicator The LED on your car's dashboard or console will inform you of the system status: LED Condition Off On Flashing Flashing in cycles Meaning System is disarmed Protected valet mode System is armed TotalRecall of the last activated trigger or sensor (see page 4) Prior Intrusion Attempt Alert When you remotely disarm, if you hear 3 chirps instead of the usual one chirp it means that a trigger or sensor was activated in your absence. AutoTestingTM Each time you remotely arm, it tests all triggers and sensors. If a trigger malfunction is found, you will be visually and audibly alerted immediately with 4 chirps and flashes instead of the usual 2. If a sensor is malfunctioning, you will receive the usual 2 chirps and flashes, then, 5 second later, there will be 4 chirps and flashes. Automatic Malfunction Bypass To provide the utmost protection even if a system component malfunctions, the system will automatically bypass the faulty point and arm all other triggers and sensors until you can have the system serviced by your local Authorized Dealer. 3 TotalRecallTM The system's non-volatile memory records the identity of the last activated or malfunctioning trigger or sensor, which allows your installer to instantly track down a malfunction and save you servicing costs. To identify the trigger or sensor held in the system's non-volatile memory, simply perform the following procedure: 1. Press button I to "arm" the system, then again to "disarm. " 3. The LED will blink several times, pause, then repeat the blink cycle 4 times. Count the number of blinks in one cycle and refer to the chart that follows: Number of LED blinks per cycle 1 blink 2 blinks 3 blinks Trigger/Sensor that Last Activated or Malfunctioned Magnetic Resonance Sensor Door trigger Trunk or hood trigger How to Interpret the Chirps and Parking Light Flashes When you press the remote control buttons, the system will respond with chirps (unless you have the chirp muting feature turned on) and flashes the parking lights to indicate the system status. [. . . ] Immediately flick the valet switch back and forth, counting the number of chirps you hear. You will hear one or more chirps (as noted in the "program completion confirmation" section) to confirm that you have changed the feature setting. Programming Table for User-Selectable Features Feature AutoArming AutoArm & Lock Arm/Disarm Chirp Confirmation # of Factory flicks & setting chirps ON 4 Secondary action Program completion confirmation 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step 1 chirp 3 seconds after last step Result Change state from ON to OFF or vice-versa Change state from ON to OFF or vice-versa Change state from ON to OFF or vice-versa -- OFF 5 -- ON 6 -- FACT -- False Alarm Control and ON/OFF Test/Tampering Warning Add a New Remote to Channel 1 (arm/disarm) 7 -- Change state from FACT to Tampering Warning -- 8 Press remote control button I 1 chirp Button I/channel 1 code of new remote control has been memorized 5 Feature Add a New Remote to Channel 2 (optional remote accessory) Add a New Remote to Channel 3 (silent arm/disarm) # of Factory flicks & setting chirps Secondary action Program completion confirmation Result -- 10 Press remote control button II 3 chirps Button II/channel 2 code of new remote control has been memorized -- 9 Press remote control buttons I+II (or button III of the optional 4-channel remote control) 2 chirps Button I+II/channel 3 code of new remote control has been memorized User-Programmable Remote Controls Your system will respond to as many as four remote controls regardless of each remote control's individual digital coding. Thus, you can buy additional remote controls, including the super-high-security 4. 3-billion-code PremierTM remote controls, from any Authorized Clifford Dealer. [. . . ]