User manual CLIFFORD REMOTE KEYLESS ENTRY

[. . . ] Interface for Factory-Installed Theft Deterrent Device--If your vehicle has a factory-installed, non-remote control, theft deterrent device, the Remote Keyless Entry System turns it into a remote controlled car alarm!So when you remotely lock/unlock your vehicle's doors, the Remote Keyless Entry System will automatically arm/disarm your theft deterrent system. Remote Trunk Release Capability--Allows you to activate the trunk release from up to 100 feet* away. To prevent unintentional activation, an electronic interlock assures that the trunk release may be remotely activated only when the vehicle's doors are unlocked (may require an optional relay). [. . . ] Remotely Controlling Your Factory-Installed, Formerly Non-Remote-Control Alarm If your vehicle is equipped with a factory-installed, non-remote-control theft deterrent device, the Remote Keyless Entry System includes an interface that turns it into a remote-controlled alarm system. So you can remotely lock/unlock your vehicle's doors and simultaneously arm/disarm the alarm -- with a single touch of button 1 on your remote control! * Some countries require less range. 5 The Optional Remote Keyless Entry System PLUS If your Remote Keyless Entry System has been equipped with the Plus option package, your system has even greater functionality (your local Authorized Clifford Dealer can add the Plus option to your Remote Keyless Entry System anytime). The package includes our patent-pending PlainViewTM Coded Valet Switch that allows you to easily expand and customize the features of your Remote Keyless Entry System system. Using the PlainView Coded Valet Switch Before changing any feature settings or placing the system in UltraSecureTM Valet Mode (see page 8), you must first enter your secret valet code to tell the system you are authorized to make these changes. Your valet code will be any one-to-three digit number of your choosing. NOTE: If you temporarily lose the use of your remote controls, you can turn off the starter interrupt feature of the system by enabling valet mode. Definitions: Digit: A digit is defined as any number from 1 to 9, inclusive. Valet code: A valet code may be 1 to 3 digits: A one-digit code = X = any number between 1-9. A two-digit code = XY = any number between 11-99 (excluding those numbers with zeros). A three-digit code = XYZ = any number between 111-999 (excluding those numbers with zeros). PlainView Switch: A rocker-switch mounted on the dashboard or console with three positions: 1. ) Latched 2. ) Center 3. ) Spring-loaded momentary. When you press the latched side, the switch remains in its latched position. When you press the momentary side, the switch bounces back to its center position. Entering a digit: To enter a digit, you tap (press and release) on the momentary side of the PlainView switch the number of times corresponding to the numeral of the digit to be entered, followed by pressing to the latched side, then returning the switch to its center position. The system has automatically reverted to the previous code. Example of setting a new valet code: Let's say you want to change the valet code from its original single-digit "2" code to a double-digit code of "31. " You would do the following: Turn the ignition on, enter your current code, tap the momentary side of the PlainView Switch 6 times, press the latched side, then enter the new code: momentary, momentary, momentary, latched, momentary, latched, center. Wait for the system to exit programming mode (indicated by 1 LED flash), then turn the ignition off. That's all there is to it, but be sure to perform step 6 above to verify your new code. 7 PlainView Coded Valet Switch LED Indicator The LED status indicator in the switch is used to communicate the operational status of your Remote Keyless Entry System system: LED Condition Off On One Flash Two Flashes Flashing Meaning Doors are unlocked, you may enter the vehicle. Doors are locked and system is protecting your vehicle. UltraSecure Coded Valet Mode Whenever your vehicle is to be washed, serviced or valet parked, you must put the system in valet mode if the automatic Starter Interrupt and SelfLock features are enabled. To enable valet mode 1. Turn the ignition switch to its "ON" position or start the engine. Enter your secret valet code on the PlainView switch, then return the switch to its center position. Once you have entered valet mode, the system's LED will glow continually for ongoing visual confirmation of valet mode. Keyless entry in valet mode: Even if valet mode is enabled, you can still remotely control the convenience features. For instance, simply press button 1 as you normally would to unlock the doors. The doors will unlock (as indicated by one flash of the parking lights) and the interior lights will illuminate. Press button 1 again and the doors will lock (as indicated by two flashes of the parking lights), but the starter interrupt feature will not engage, so the vehicle may be driven by anyone with the car key. You can also use the remote control's other button to activate options such as a remote trunk release or remote engine starting. To exit valet mode 1. Turn the ignition switch to its "ON" position or start the engine. [. . . ] Repeat steps 1-6 for any other features or remote buttons you wish to program. Programming Table for User-Selectable Features Feature Automatic Starter Interrupt Automatic "passive" SelfLocking Doors Valet Code AutoLock/ AutoUnLock Add a New Remote to Channel 1 (arm/disarm) # of Factory momentary setting presses Off 4 Secondary action Program completion confirmation 1 LED flash Result -- Change state from ON to OFF or vice-versa Off 5 -- 1 LED flash Change state from ON to OFF or vice-versa "2" On 6 7 See How to Set Your Valet Code on page 7. -- 1 LED flash Change state from ON to OFF or vice-versa Button 1/channel 1 code of the new remote control has been memorized -- 8 Press remote control button 1 within 10 seconds. 2 LED Flashes continued. . . 10 Feature Add a New Remote to Channel 2 (optional remote accessory) Add a New Remote to Channel 3 (optional remote accessory) Headlight Duration # of Factory momentary setting presses Secondary action Program completion confirmation Result -- 9 Press remote control button 2 within 10 seconds. 2 LED Flashes Button 2/channel 2 code of the new remote control has been memorized -- 10 Press remote control button 3 within 10 seconds. Button 3/channel 3 code of the new remote control has been memorized 15 Seconds 11 See Programming the Headlight "ON" Duration on page 9. Example To change the Automatic ("passive") SelfLocking Door feature from its factory setting of "OFF" to "ON, " you would do the following: Turn the ignition key to the "ON" position. The switch's LED will light to indicate that the system is in programming/valet mode. Then immediately tap and release the momentary side of the PlainView switch 5 times. [. . . ]