User manual CLIFFORD INTELLIVOICE IQ

[. . . ] World-Class Auto Security TM intellivoice IQ Owner's Manual Table of Contents Standard Features of the IntelliVoice-IQ . Anti-CodeGrabbingTM (ACG) with Random Code Encryption Enhanced AutoArmingTM . Remote controlled valet mode entry and exit Keyless entry in valet mode . Remote controlled override of one or both sensor zones FACT -- False Alarm Control and Test . [. . . ] To help you count, you will hear a chirp each time you press the momentary side. To enter 31 as your new code, you would press the switch in this manner: momentary, momentary, momentary, latched (you'll hear 3 chirps to confirm the first digit), momentary, latched (1 chirp to confirm the second digit), center. Wait 3 seconds until you hear 2 chirps, indicating the new code has been accepted. Turn off the ignition to exit program mode (you'll hear a 3-chirp confirmation). VERY IMPORTANT: You must immediately test your new secret valet code: Turn on the ignition, enter your new code, then flip the switch to its latched position. If it does not, the new code you programmed and the one you just entered do not match. In such a case, the system will revert to the previous code. Remote controlled valet mode entry and exit You can even enable or exit valet mode by transmitting channel 9 (LevelShift twice, then button 1). Two parking light flashes will confirm that you have remotely enabled valet mode and the system will say "ENABLED. " A single flash confirms valet mode exit. Keyless entry in valet mode Even if valet mode is enabled, you can still remotely control the convenience features. For instance, simply press button 1 (channel 1) as if you were disarming and the doors will unlock (indicated by one parking light flash) and the interior lights will turn on. You can also use the other channels to activate options such as a remote trunk release or remote engine starting. 12 Remote controlled sensor adjustments Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors. But IntelliVoice-IQ lets you can adjust sensitivity electronically without even knowing where the sensor is mounted!If the setting(s) of the Proximity Sensor are either too sensitive or not sensitive enough, you may individually test and adjust the settings of each zone with the following procedure: 1. Disarm the system with the remote control, open the driver's window, then select the sensor zone you wish to adjust: a. Ideally, it should chirp when you lean over the driver's seat, but remain silent when you lean toward the window. Ideally, it should only chirp when you are moving within one foot of the vehicle. If you are not satisfied with the detection level and wish to increase sensitivity, press button 2 on your remote control. Each time you increase sensitivity, the siren will chirp in higher and higher pitched tones to confirm the higher sensitivity setting. There are 32 sensitivity levels for the Proximity Sensor's interior zone; 16 for the less critical warning zone. Repeat steps 2 and 3 until you are satisfied with the sensitivity, then press button 1 to record the new sensitivity setting and exit the sensor test/adjust mode (you'll hear three chirps to confirm exit). You may now either repeat steps 1­4 for the other sensor zone, or press button 1 again to arm the system. It really isn't, there's just a lot of explanation of what's happening with each step. [. . . ] If no action is taken for the next 60 seconds, the system automatically exits program mode, perfect if you program while driving or if you forget to turn off the ignition. To reset the system to its previous settings, just repeat the steps in example 2. Adding new remote controls For other drivers in your family, or if you wish to control IntelliVoice-IQ systems on your other cars with the same remote control, you can buy additional remote controls from any Clifford Dealer (or call our Customer Service Department at 800-824-3208) and program them into the system yourself. Each IntelliVoice-IQ will respond to as many as four 12-channel ACG remote controls. To add a new remote control to the system, use the procedures noted in the User-selectable features section on pages 17-21. [. . . ]