User manual CLIFFORD INTELLIPAGE

[. . . ] World-Class Auto Security TM IntelliPage Owner's Manual The IntelliPage system is covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375, 5, 467, 070 and other patents pending. WARNING The IntelliPage system is designed to be used ONLY on a fuel-injected, gasoline or diesel powered vehicle with an automatic transmission. Installing an IntelliPage on a vehicle that has a manual transmission poses an EXTREME SAFETY RISK!Never install a Clifford remote engine starting product on a manual transmission vehicle. Always exercise good judgment and common sense when using the remote starter: · NEVER remotely start the vehicle in an enclosed area without sufficient ventilation. · NEVER engage the ShortStop nor one or both AutoStart features if the vehicle is in an enclosed area without adequate ventilation. [. . . ] You will hear a chirp if the strike was firm enough to trigger the alarm zone of the sensor. Piezo Sensor warning zone: "Thump" the top of the window pillar with somewhat less force than noted above. You will hear a chirp if the strike was firm enough to trigger the warning zone of the sensor. If you are not satisfied with the detection level and wish to increase sensitivity, press button 2 on your remote control. Each time you increase sensitivity, the siren will chirp in higher and higher pitched tones to confirm the higher sensitivity setting. There are 32 sensitivity levels for each of the Proximity Sensor's two zones; the alarm zone of the Piezo Sensor also has 32 levels, while the less critical warning zone has 16 steps. Repeat steps 2 and 3 until you are satisfied with the sensitivity, then press button 1 to record the new sensitivity setting and exit the sensor test/adjust mode (you'll hear three chirps to confirm exit). You may now either repeat steps 1­4 for the other sensor and/or sensor zone, or press button 1 again to arm the system. It really isn't, there's just a lot of explanation of what's happening with each step. Give it a try. Remote controlled override of one or both sensor zones Transmitting channel 10 within 10 seconds of arming the system will override the exterior warning zone of the Proximity Sensor (you'll see 4 parking light flashes to confirm the zone override). Transmitting channel 10 again within the 10 second period will override both zones of the sensor for those times when you must leave a passenger or pet in the vehicle. The sensor zones are automatically restored the next time you arm the system. How to interpret the LED status indicator The LED on your car's dashboard or console will inform you of the system status: LED Condition Off On Flashing Pause between flashes Meaning System is disarmed and in normal operating mode (i. e. , valet mode is off) Valet mode is on, the vehicle can be driven or serviced without having to disarm System is armed and protecting your vehicle Either a malfunction occurred or an intrusion was attempted (see pages 24-25) Automatic battery-saving mode To conserve vehicle battery power (the LED draws more current than the entire control unit) if the system has remained continuously armed for 48 hours, the flash rate will automatically slow to half the normal rate. After 96 hours, it slows to one-quarter. 22 NightVisionTM All of the following NightVision Headlight Automation features are built into your IntelliPage: n User-selectability: You may turn the NightVision features on or off whenever you wish (see User-Selectable Features on pages 35-39). n When driving at dusk: The system automatically turns on the headlights. n When driving at dawn: The system automatically turns off the headlights. n Precision activation: NightVision automatically and unerringly turns the headlights on or off only when necessary. For instance, if it is dark when the car's engine is started with the key, NightVision instantly turns on the headlights (if the engine was remotely started, the headlights will instantly turn on when you turn your key to the "START" position). However, when the vehicle is driven under an overpass in daylight, the headlights will not turn on. Even more importantly, when passing through a very brightly lit area at night, the headlights will not switch off. However, if you drive into a dark parking structure during the day, NightVision will turn on the headlights within five seconds of entering the structure. n When you park your car at night: NightVision keeps the headlights on for any duration of your choice between 1 sec. (factory preset to 30 sec. ; to change the duration, see User-selectable features on pages 35-39) after you turn off the engine to light your path away from the vehicle. [. . . ] If you wait more than 10 seconds, the system automatically jumps back to the "Feature Select" position. This is the "stand-by" position: ready for entry of a new programming selection. If no action is taken for the next 60 seconds, the system automatically exits program mode, perfect if you make a few programming changes while driving. Reset all features Whenever you wish, you may reset all the user-selectable features to their factory settings (factory settings are noted in bold type on the Table of User-Selectable Features). Doing so will reset all user-selectable features except your current valet code, nor will it erase the remote controls programmed into your system (to do this, use the column 2, row 6 Erase all remotes feature). To reset all other user-selectable features, use the following procedure: 1. [. . . ]