User manual CLIFFORD INTELLIGUARD 770

[. . . ] Intelliguard 770 Owner's Guide limited lifetime consumer warranty Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. [. . . ] If the Warning Zone response is triggered, the LED will not report it. Zone - Number of LED Flashes 1 2 3 4 5 6 7 8 9 10 Description Proximity sensor Omnisensor Mux 1 trigger - for optional sensors Door switch trigger Instant trigger - trunk Instant trigger - hood Ignition trigger Mux 2 trigger - for optional sensors BlackJax activation Power interrupt Orange Blue Dealer-Installed Options anti-code grabbing (ACG) This unit features Anti-Code Grabbing (ACG) with Random Code Encryption. This means the receiver and remotes each use a mathematical formula called an algorithm to change their code each time the remote is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. 18 high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet® Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet® Mode. This applies to all states of the system including arm, disarm, and Valet® Mode. power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet® Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery and prevents the system from draining the battery. Power Saver Mode takes over under the following conditions: © 2 0 0 6 d i re c t e d e l e c t ro n i c s 19 Power Saver when the system is armed: After the system has been armed for 48 hours, the LED will flash at half its normal rate, decreasing the system's current draw. Power Saver in Valet® Mode: When the system enters Valet® Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet® Mode, the LED will shut off. If the system remains in Valet® Mode, the LED will come back on the next time the ignition is turned on and then back off. programming options Programming options control what your system does during normal operation, and require few or no additional parts. Following is a list of the program settings, with the factory settings in bold: Active arming (only with the remote) or passive arming (automatic arming 30-seconds after the last door is closed). ON: The doors will lock three seconds after the ignition is turned on unless a door is open. Auto-Unlock on/off: With this feature on, the doors will unlock when the ignition is turned off. Passive door locking (with passive arming) or active door locking (only when arming with the remote). Passive locking 20 allows the vehicle's doors to lock when the security system passively arms (after the 30 second countdown). Panic mode enabled/disabled: Some states have laws against siren capability while driving. Full trigger response 30, 60, or 90 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance. False Alarm Control Technology (FACT II) on or off: Please refer to the FACT II section of this guide for a complete explanation of how FACT II operates. [. . . ] Turn ignition off, siren chirps 3 times as confirmation of exiting programming. note: If ignition remains on after entering PIN code and no action for 10 seconds, unit will automatically exit programming mode without chirps. blackjax off warning indicator Each time the ignition is turned off when BlackJax is bypassed the LED will blink 10 times as warning that the BlackJax has been temporarily bypassed. 36 audio sensor The 506T Audio Sensor is a low-current device that provides an added level of protection to an existing security system by detecting sounds that have the acoustic signature of breaking glass or metal-to-glass impacts. adjusting the omnisensor The Omnisensor is designed for ease of adjustment by the user and to give the ultimate in impact detection without the possibility of false triggers that are common with less sophisticated sensor. While adjusting this sensor it is required that you strike the vehicle with the amount force that is desired for the system to trigger. note: DO NOT strike window glass or flat sheet metal panels that can dent easily. It is recommended that you only strike the metal pillars between the windows, they are structurally sound enough not to dent. ONLY strike the pillars using the heel of your hand, it is more than sufficient for the sensor distinguish as a theft attempt. 1. [. . . ]