User manual CLIFFORD GP500

[. . . ] Other features can be accessed as noted in the following chart: OTHER FEATURES 4 GP500 QUICK REFERENCE: REMOTE CONTROL FUNCTIONS Function Arm or disarm Silently arm or disarm Instant AutoArming Bypass (press and hold button for three seconds while system is disarmed) Dual-Level Piezo Sensor Warning Level Bypass (press button within 10 seconds after arming the system) Dual-Level Piezo Sensor Total Bypass (press and hold button for three seconds within 10 seconds after arming the system) Digital Tilt/Motion Sensor Warning Zone Bypass (press buttons within 10 seconds after system is armed) Digital Tilt/Motion Sensor Total Bypass (press and hold buttons for three seconds within 10 seconds after system is armed) Dual-Level Piezo Sensor Adjustment (press and hold buttons for three seconds while system is disarmed. See page 21 for complete instructions) Unassigned* Unassigned* * Can be assigned to Clifford ACG-2 systems on your other vehicles. Press button(s) I II III III III II + III II + III II + III I + II I + III User's Manual/299 5 ACG-2TM (Anti-CodeGrabbing 2TM) Clifford's ACG-2 protects your motorcycle from thieves' remote control "cloning" devices that are used to record the disarming code transmitted from your remote. Automatic remote control low-battery warning If your remote control battery is very low, you will hear five rapid chirps when you disarm rather than the single chirp that you normally hear. [. . . ] To adjust the warning level of the sensor, you must have the ignition turned ON, to adjust the trigger level of the sensor, turn the ignition OFF. · Three chirps indicate that you are at the top or bottom of the 16 step incremental range. One chirp signals an alarm trigger level detection, two chirps signal a warning level detection. Press button I on the remote control to save the new settings. 10 GP500 TO REMOTELY BYPASS THE WARNING ZONE: During the first 10 seconds after arming the system remotely, press button III on the remote control. The system provides four indicator light flashes when the warning level is bypassed. During the first 10 seconds after arming the system remotely, press button III on the remote control and hold for three seconds. The system provides four indicator light flashes to indicate when the warning level is bypassed, and another four indicator light flashes when both levels are bypassed. TO REMOTELY BYPASS BOTH ZONES: Helmet Theft Protection System Loop the helmet theft prevention wire through the item to be secured. Close the seat making sure it is firmly latched and arm the system. User's Manual/299 11 False Alarm Prevention & FACTTM With Clifford's patented FACT (False Alarm Control and Test) feature, you'll never experience repeated false alarms. If the siren sounds, DO NOT remotely disarm the system; allow it to run for the full 30-second siren duration. Before sounding the siren a second time, the system automatically checks for another activated sensor or trigger. Should the siren sound again, you will know for sure that someone is tampering with your motorcycle. (If you wish, you may turn off FACT, see the Table of Programmable features on page 32. ) How to interpret the chirps and flashes Chirps/flashes Meaning You have disarmed the system You have armed the system Disarmed but there was an intrusion attempt while you were away (see Smart prior intrusion attempt on the following page) Armed but the Helmet Theft Prevention system or sensor has malfunctioned and has been bypassed (see Smart Autotesting below). 1 2 3 4 12 GP500 How to interpret the LED status indicator LED Condition Meaning System is disarmed System is armed AutoArming Countdown System is disarmed but Immobilisation points are engaged (see page 15) Off Flashing Steadily (Ignition off) Flashing rapidly (ignition off) Flashing slowly (ignition on or off) Pause between slow Either a malfunction (see Smart AutoTesting below) or flashes (ignition on) an intrusion was attempted (see Smart prior intrusion attempt alert on page 27) Automatic Battery-Saving Mode To conserve motorcycle battery power (the LED draws more current than the entire control unit), if the system has remained continuously armed for 24 hours, the flash rate will automatically slow to half the normal rate. User's Manual/299 13 Smart AutoTestingTM Each time you remotely arm the system, it tests all triggers and sensors. For example, if the Helmet Theft Prevention System is active, you will receive the usual 2 chirps and flashes, then, 5 seconds later, there will be 4 chirps and 4 flashes. If a sensor is malfunctioning, you will receive the usual 2 chirps and 2 flashes, then, 10 seconds later, there will be 4 chirps and 4 flashes. Note that when you receive these indications that the system will still arm even though a trigger or sensor is malfunctioning. NOTE: Since this is a warning indication, you will hear the 4 chirps even if you use the chirp muting feature. n Specific malfunction identification: The system can also indicate the specific trigger or sensor that is malfunctioning. If you get the 4-chirp/4-flash signal upon arming, perform the following to identify the malfunctioning trigger or sensor: 1. Count the number of flashes in one cycle between pauses (for your convenience, the flash cycle repeats a total of 5 times) and refer to the following chart: 14 GP500 LED flashes Meaning Ignition switch was turned on Activation of Digital Tilt/Motion Sensor Activation of Dual-Level Piezo Sensor Activation of helmet theft prevention device Optional additional trigger was activated (such as a seat trigger) Activation of Panic Feature/Remote Vehicle Locator Three or more incorrect PIN codes were entered via the PlainView 2 switch Low remote control battery 1 flash 2 flashes 3 flashes 4 flashes 5 flashes 6 flashes 7 flashes 8 flashes Automatic malfunction bypass with AutoReMonitoringTM Even if a system component malfunctions, the system will automatically bypass any faulty point and arm all other triggers and sensors to protect the vehicle until you can have the system serviced by your local Authorized Clifford Dealer. User's Manual/299 15 Smart prior intrusion attempt alert If you hear three chirps when you remotely disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition (or start the engine), the LED will flash 1-8 times, pause, then repeat the flash cycle 4 more times. Example To set a disarming code of 4301, you would do the following: 1. Enter program mode by turning on the ignition, entering your current PIN code, then pressing and holding the PlainView 2 D button for 3 seconds until you hear a chirp. [. . . ] Wait. Enter new 1 chirp=new PIN code PIN code is again, system accepted provides 2 chirps. Press 1 chirp=all button I buttons are again, programmed system provides 2 chirps. Auto Program New GP500 Remote 9 Press remote control button I User's Manual/299 21 Feature Factory Setting No. of times to press the D button Secondary Action Press remote control button to be assigned to this function Press remote control button to be assigned to this function Press button to be assigned to this function Program completion confirmation Additional Action Press button to be assigned again. System provides 2 chirps. Program other Clifford ACG-2 Remote to Arm/Disarm GP500 - 10 1 chirp= button is ready to be assigned to the function Program other Clifford ACG-2 Remote to Silent Arm GP500 - 11 2 chirps= button is ready to be assigned to the function Program other Clifford ACG-2 Remote to Bypass Instant AutoArming for GP500 - 12 3 chirps= button is ready to be assigned to the function 22 GP500 Feature Factory Setting No. [. . . ]