User manual CLIFFORD 8000

[. . . ] The Science of SecurityTM INTELLIGUARD 8000 Complete Owner's Manual USA Headquarters 20750 Lassen Street Chatsworth, California 91311 1-800-CLIFFORD or 1-800-824-3208 or 1-818-709-7551 Canada Headquarters 4513 Dobrin Street Montreal, Quebec H4R 2L8 1-800-361-3444 or 1-514-332-4444 UK Headquarters Boundary Business Court 92/94 Church Road Mitcham, Surrey CR4 3TD 0800 929949 or 0181 646 8440 Germany Headquarters Schlesische Straße 27 10997 Berlin 0130 115 681 oder 030 611 2602 Mexico Headquarters Saratoga 804 B, Col. 01 800 021 2543 o 5 605 0382 Clifford systems are covered by one or more of these Clifford Electronics USA patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375; 5, 467, 070; 5, 650, 744 and other patents pending United Kingdom customers: Please pardon our American English references and spellings. Trunk and hood references indicate the boot and bonnet, respectively; parking lights are indicator lights; gas/gasoline is petrol; a parking lot is a car park. Standard Features The following are standard features of this system. Some vehicles may require optional parts/wiring and a few are incompatible with some features. þ þ þ EC-approved (Europe) Lifetime warranty (see terms & conditions) One master remote control, one companion remote n Extended range n ACG 2TM Anti-CodeGrabbing protection n Low remote control battery warning þ þ þ þ Power door lock control Parking Lot HighLight vehicle locator* Ignition-switch controlled AutoLocking/AutoUnlocking Remote panic feature n Smart panic locking/unlocking based on whether the engine is on/off þ PlainView 2TM coded valet mode n Select your own secret code þ Built-in timer circuit for optional timed headlight activation or turbo timer Built-in parking light flasher Courtesy light(s) turn on when you disarm with the remote Smart AutoTesting self-diagnostics n With specific trigger & sensor identification þ þ þ þ BlackJax anti-carjacking/self-recovery system Remote controlled valet mode Built-in two-point AutoImmobilizer Remotely Adjustable Dual-Zone Proximity Sensor 4 detects inside and outside the passenger compartment n Remote sensor zone override þ þ þ þ Malfunction AutoBypass n Automatic trigger remonitoring if trunk/hood was open when þ Smart DataPort input n For complete optional control of your system via your arming Windows PC n For smart accessory interfacing þ þ þ Smart Prior Intrusion Attempt Alert n With specific trigger & sensor identification FACT anti-false alarm circuitry Passive AutoArming if you forget to arm with the remote control n Lock upon AutoArming self-locking n Visual AutoArming countdown confirmation n Instant AutoArm bypass þ TotalRecall 8-event trigger/sensor memory report n With specific trigger & sensor identification þ þ þ Remote control code learning Clear all remotes if ever lost or stolen LED status indicator n Flash indications reveal status n Automatic battery saving mode þ High-Output Medallion Siren n Selectable Personalized Siren Sounds* n Remote controlled chirp muting n Selectable QuietChirps/LoudChirps n Long-term selectable chirp muting n 30/60/90-second selectable siren duration* n Remote siren silencing without disarming if falsely triggered þ þ þ Multiple vehicle control from the same remote control Multiple sensor/trigger inputs User-programmable features n SecureAccess coded programming n Programmable even while driving *Not available on European models in compliance with EC95/56 þ Smart optional remote trunk release prevents falsing NOTE: Your system MUST be installed by an Authorized Clifford Dealer in accordance with the instructions we supply them. [. . . ] When set to "trigger only" the basic siren wail will sound if a sensor is activated, but the Personalized Siren Sounds will play if the hood, trunk or a door is opened. See User-selectable features (column 1, row 3). *Not available on European models in compliance with EC95/56 % Remotely Adjustable Digital Dual-Zone Proximity Sensor 4 Your system's Digital Dual-Zone Proximity Sensor 4 detects movement inside the passenger compartment and very near your vehicle. If a thief lingers very close to your windows, a warning tone sounds; if he were to lean into the passenger compartment, the primary zone of this sensor would trigger the full alarm. These waves pass through nonmetallic materials like plastic, carpet, glass and wood. However, metal and metallic paint, plastic and even some metallic film window tinting materials will interfere with or completely block the radar waves. As such, it is not unusual that the Proximity Sensor zones may need a little readjustment when you first have the system installed. In some instances, your Clifford installer may need to try a different location for the sensor. If needed, you can adjust sensitivity of these sensor zones via your remote control as described in the following section. To prevent falsing, system sensors are bypassed when the engine is remotely started (if you have the IntelliStart 4 option). Metal above or near the Proximity Sensor will have a significant impact on operation. You should not place coins, CDs, cassettes (due to the iron oxide tape) or other metallic objects above or near where the sensor is mounted. Ask your Authorized Clifford Dealer about these optional sensors that will further enhance the security of your vehicle: n n n Glass Tampering Sensor: Today's thieves shatter vehicle windows with a small metal punch device that does not create any vibrations for an impact sensor to detect. The Glass Tampering Sensor detects the sound of glass breaking, and glass tampering attempts, and will trigger the alarm. Dual-Zone OmniSensor: Uses our most advanced DSP (digital signal processing) to detect theft-related impacts and vibrations. Advanced discrimination algorithms differentiate better than any other sensor between common environmental conditions (such as a heavy truck rolling by) and genuine threats to your vehicle. Digital Tilt/Motion Sensor: Detects less than one degree of lifting or any minute motion of the vehicle while completely ignoring all other conditions that falsely set off all other sensors. Even if you park on a hill, the Digital Tilt/Motion Sensor will accurately respond to the first hint of tampering to reliably protect your wheels and entire vehicle. Remote controlled sensor adjustments If the setting(s) of the sensor zones are either too sensitive or not sensitive enough, you may test and adjust them with the master remote control: 1. Select which sensor to adjust: · Optional OmniSensor: Transmit channel 15 on the master remote (LevelShift three times, then button 3). · Proximity Sensor: Transmit channel 16 on the master remote (LevelShift three times, then button 4). Adjustment of optional OmniSensor: To test the primary (alarm) zone, press button 4 (you will hear a 2-chirp confirmation), then firmly "thump" the top of the A-pillar (the area between the side windows near the roof) heel of your fist. If the impact is strong enough to trigger the primary zone, you will hear a siren chirp. To change sensitivity, press button 2 (you will hear a 2-chirp confirmation), then firmly thump the top of the A-pillar with the amount of force that you want set off the alarm (a single chirp will acknowledge the thump). You may now press button 3 to adjust the warning zone (as noted in 3a. below), or press button 1 to fully exit the OmniSensor adjustment mode (you will hear 3 chirps). [. . . ] Press the blank button to turn on this sound or the button to turn it off. NOTE 3: You'll hear two chirps to indicate all remotes have been cleared from memory. You must now add new/existing remotes with the "Add master remote control" feature and/or the "Other vehicle`s remote" feature. NOTE 4: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the ignition (you'll hear 3 chirps to confirm program mode exit). [. . . ]