User manual CLIFFORD 700

[. . . ] World-Class Auto Security TM intelliguard 700 Owner's Manual All IntelliGuard Series systems are covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375 and other patents pending Table of Contents Standard Features of the IntelliGuard 7OO . 14 FACT -- False Alarm Control and Test Fault-ProofTM starter interrupt . 16 Smart prior intrusion attempt alert High-output MultiSound MedallionTM Siren . 22 EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps . [. . . ] Now you can control these features any time you wish from outside your vehicle with just your remote control. Here's how: QuickAccess Valet Mode: To enter valet mode remotely, transmit channel 9 (press the LevelShift button twice, then button 1). The parking lights will flash twice and the dashboard LED will stay on to indicate the system is in valet mode. To exit valet mode remotely, transmit channel 9 again and the system will confirm exit of valet mode with one parking light flash and the LED will turn off. (NOTE: If you enter valet mode via the remote control, you must exit valet mode in the same manner. If you use the PlainView switch to enter valet mode, you must use the switch to exit valet mode. ) QuickAccess Sensor #2 Override: This is a great convenience feature if you have an optional Proximity Sensor passenger compartment sensor and need to leave your pet in the vehicle. Within 10 seconds of remote arming, transmit channel 10 (LevelShift twice, then button 2). The parking lights will flash four times to confirm that the optional sensor #2 will not trip the system. QuickAccess Sensor Testing & Adjustment: Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors. You can adjust sensitivity electronically without tools and without even knowing where the sensor is mounted!If you find the current setting(s) of the Magnetic Resonance Sensor to be either too sensitive or not sensitive enough, you may individually test and adjust the sensitivity settings yourself. b. Warning zone: Transmit channel 12 (LevelShift twice, then button 4). Test the current sensitivity setting by "thumping" the window pillar with your fist. If the strike is strong enough to trigger the selected zone, you will hear a chirp. Strike firmly when testing the primary zone, less firmly to trigger the perimeter warning zone. Each time you increase sensitivity, the siren will chirp in higher and higher pitched tones to confirm the higher sensitivity. Repeat steps 2 and 3 until you are satisfied with the sensitivity, then press button 1 to record the new sensitivity setting and exit the sensor test/adjust mode (you'll hear three chirps to confirm exit). You may now either repeat steps 1­4 for the other sensor zone, or press button 1 to arm the system. Sound complicated?It really isn't, there's just a lot of explanation of what's happening with each step. Give it a try. 14 FACTTM-- False Alarm Control and Test With FACT, you'll never experience repeated false alarms. If the siren goes off, DO NOT disarm the system; let it run for the full siren duration of 30 or 60 seconds (user-selectable). Before sounding the siren a second time, the system automatically checks for another activated trigger to verify that an intrusion is in progress. [. . . ] Higher and higher pitched tones confirm each sensitivity increase, lower and lower tones confirm each decrease. Repeat until the sensor is set to the sensitivity you wish, then press button 1 to record the new sensitivity level and exit sensor test/adjust mode (you'll hear 3 chirps to confirm this). You may now either arm the system with channel 1 or enter the vehicle. NOTE 7: Use the same procedure as NOTE 7, but strike the window pillar lightly. NOTE 8: Immediately flip the switch to its latched position, then enter the new code that you wish to use. Make sure to return the switch to its center position when complete, then wait 3 seconds (you will hear two chirps when the system has accepted the new code). [. . . ]