User manual CLIFFORD 650

[. . . ] PrimeStart 650 Installation Manual PrimeStart 650 Installation Manual Table of Contents Important Information . 26 1 PrimeStart 650 Installation Manual Important Information Recommended Installation Tools Voltmeter Wire Strippers Electric Drill & Bits Phillips Screwdriver Convoluted Tubing * Solder Gun * Wire Crimpers Shrink Tube or Electrical Tape * Optional Recommended Procedures 1. Make all wiring connections with the supplied solderless crimp connectors. Route the small and large RED, RED/WHITE and BLACK wires from the control unit directly to the battery. [. . . ] Channel 9 Accessory Output The BLUE/YELLOW wire provides a 0. 75 second output when the SILENT and START buttons are pressed at the same time for 1-2 seconds. If the SILENT and START button are continually pressed, the output will stay at ground as long as the buttons are held. This output can be used for optional accessories such as a fuel filler door release or any other accessory requiring a (-) input. Remote Start Armed Signal (-) Output The GRAY/BLACK wire will provide a continual ground output for as long as the vehicle is in the remote start mode. This output can be used for additional ignition, starter or heater/AC relays, as well as VATS, Passlok and Passkey bypass. 11 PrimeStart 650 Installation Manual Factory Alarm Disarm (-) Output The GRAY/WHITE wire will provide a 0. 75 second ground output when the START button is pressed. Use a voltmeter to find the wire(s) that show +12 volts when the ignition key is in the "ON" position, 0 volts while the starter is cranking and +12 volts while running. I WARNING:toReview thethe starterBulletin" and diagrams on pages 1. Use a voltmeter to find the wire that shows +12 volts while the ignition key is in the "CRANK" position only and 0 volts while the key is in the "OFF, " "ON" and "RUN" positions. Connect the YELLOW wire to the ignition switch side of the starter wire. Connect the VIOLET wire to the starter solenoid side of the starter wire. 13 PrimeStart 650 Installation Manual Remote Engine Start Neutral Safety Switch Bulletin A neutral safety switch is a mechanism on almost every vehicle equipped with an automatic transmission. The neutral safety switch prevents the vehicle from starting while the gear shift selector is in "Reverse" or "Forward" gear positions. A small group of vehicles use a combined neutral safety switch. Type "A" (separate) The mechanical neutral safety switch is located between the ignition switch and the starter solenoid. The starter wire runs directly from the back of the ignition switch to the neutral safety switch and then to the starter solenoid. When adding a remote engine starter, make starter wire connections as close to the ignition switch as possible to ensure your connections are between the ignition switch and the neutral safety switch. Type "B" (combined) Some vehicles combine the neutral safety switch and the steering column shift mechanism together. The starter wires run from the "combined" switch directly to the starter solenoid. The remote start wire connection cannot be made between the ignition switch and the neutral safety switch. As a result, if the vehicle was left in gear with the key in the ignition and not in the locked position, the vehicle could move forward or backward if a remote start attempt was made. The combined type neutral safety switch requires an additional relay to prevent the vehicle from remote starting while the key is in the ignition. Install the complete remote start unit and test all safety features before conducting the test procedure. Currently, the only vehicles with the combined neutral safety switch that Prime is aware of are General Motors trucks, GM sport utility vehicles, GM column shift passenger cars and Dodge Dakota pickup trucks. There may be additional vehicles with the combined neutral safety switch that require the additional relay. 14 PrimeStart 650 Installation Manual NOTE: Use the following test procedure upon completion of every remote start regardless of the make and model of the vehicle Test Procedure Be at least 5 unobstructed clearance at the front rear of the Make I CAUTION: andsure there isvehicle. thefeet ofsure to alert anyone near the vehicle you are testing that vehicle may move forward slightly. [. . . ] Within 10 seconds of starting the vehicle, begin flicking the valet switch on then off 15 times (counting the siren chirps). The parking lights will flash two times to confirm the RPMs have been memorized. Turn the engine off. 23 PrimeStart 650 Installation Manual Programmable Features All PrimeStart system and remote control programmable features are accomplished by turning the ignition key to the "ON" position or starting the engine and flicking the valet switch on and off a preset number of times. The PrimeStart also allows the user to add new remote controls in one step, delete lost or stolen remote controls or rearrange the factory preset remote control functions. [. . . ]